2015-2020 Genuine Kawasaki Mule PRO-FXT DXT FX DX FXR Horn Kit 99994-0455
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
The answer is no, I do not see why it This horn kit fits a variety of vehicles
There is only a momentary interruption.
The truck I have is a 2016 trans mule diesel. Considering their price tag you would think Kawa would include a horn *br>I bought this and it works *br>also kawa does not want you to know but the harnesses are already there so installation is fairly straight forward *br>Hope this helps
There is no information on a 2017 harness, but it would fit a 2015 to 2017 mule During the 2018 model year, Kawasaki Mule Pro FXT models were released.
Selected User Reviews For 2015-2020 Genuine Kawasaki Mule PRO-FXT DXT FX DX FXR Horn Kit 99994-0455
A PRO-2018 has been purchased by me A perfect fit for the horn kit. Although the instructions are interesting, they make me want to do something the hard way. Under the passenger side of the vehicle is the mounting hole. The screw holes are pre-drilled so that they can be easily accessed This is why. There is no torque limit on this screw Taping is difficult to do, and it's hard to get The best tool to use is a quality screwdriver and a bright light. It is very close to the mounting area that the wires are attached with clips. Using the fuze panel cover removed from dash and the hole in the dash near the other switches, cut the hole. The best tool for this is a dremel tool with a small disk. It is easy to locate the switch wires, and there are clips already attached Installation completed. Using a wire threader, thread the wire through the cut Take the little switch you made, and connect it to the cutouts. To use the product, turn the key on and connect the switch. APART from that, there is no need to remove ANY component.
There is a Kawasaki FXT PRO in my possession. This is *1/1. THE HORN - MOUNTING AND CONNECTING IT No parts of the cowling or grill have to be removed to access the mounting area for the horn. It is easy to remove the hood cover in order to accomplish this. When you extend your arm directly down the square tubing (passenger side), you will find a small hole in the tubing where you will need to insert the single screw which fastens the horn to the tube. The zip is cut - Tie that is used to hold two pieces together Connecting the electrical connectors in the wire cable to the horn will make it much easier to fasten it to the horn prior to screwing the horn in place A square tube is used to mount the horn. * ** 2. How to mount and attach a horn switch Take a box and place it in a safe place- The plastic square hole where the switch will be mounted will be cut out by a cutter. Remove any quick-release connectors on the dash panel, and then disconnect it Three disconnect tabs are placed at each lower corner (3 tabs on top and two at each bottom It is possible to raise tabs by using two flat-bottomed objects Cut the blades of your screwdrivers so that you can grab the heads and pull them up with your fingers. It was lying slightly in front of the steering wheel area where the cable/connectors that attach to the horn are located. I had a bit of trouble finding this cable. Don't confuse this cable with the two cylinder connectors in the vicinity of the horn switch those are the correct ones for this switch. You may have trouble finding the correct cable and connectors that go on the horn switch until you locate the right cable with the right connectors. Then that's all there is to it. I have no complaint about the horn or the switch, and I'm satisfied with both.
For not installing these at the factory, Kawasaki should be ashamed. Luckily (on a pro fxt), we can find the wires, but they aren't especially obvious. It is necessary to take off most of the front end (not as difficult as it sounds) in order to install the horn, and partially remove the dash (again, it isn't that difficult) in order The hole for the switch needs to be cut out with a Dremel tool and a small abrasive disc. Stock-like results are possible if you do it correctly. The horn sounds like the horn of a roadrunner. A beep will signal the end of the message. Not too loud, but enough to be heard. Overall, it's not bad and it looks like it was made in a This was supposed to have been done.
It has taken me weeks to find what I am looking for.
The quality is magnificent, but why doesn't the Mule come with a horn, Kawasaki?.
We love the way the horn looks and works on our Mule 2018.
Despite its ease of installation and good sound quality, this was an easy upgrade. No horns are included on UTVs. I'm not sure why this is the case.
This Horn Switch is okay, but it does not illuminate like other stock switches do. My horn wasn't a supply from Amazon, but rather an OOGA Vintage AHOOGA from Amazon. We're having a blast!.