PCB012 Power Distribution Board Self-Adapt Distributor HO N O LED Street Light Hub DC AC Voltage Train Power Control

PCB012 Power Distribution Board Self-Adapt Distributor HO N O LED Street Light Hub DC AC Voltage Train Power Control

$ 16.99

Score By Feature

Based on 158 ratings

Customer service

8.87

Value for money

8.80

Giftable

8.91

Satisfaction

9.08

OveReview Final Score

How Our Score Is Calculated

Product Description

For power input, you can choose between AC or DC voltage, and the voltage can be anywhere from 4V to 24V. As long as the output current controller can adapt to the input current, there is no limit on the input

It should come with dimmer controls for LED lights so that it can be adjusted for (Clockwise is brighter)

The output voltage controller controls controller at 3V, the output is stable at 3V controller at DIR, the output is near the input controller at 12V, the output is stable at

It is possible to support up to 28 lights with one distributor. In case you need more light, you can expand it to several boards. Please support the lights that require one distributor to feed the same current and voltage. You should not use the same distributor for lights that operate at different currents and voltages. If you wish to expand the Power Distribution Board, you can prepare another

It must be less than the input current to have a positive total output. The average LED light needs 20 mA of current. This means that a 1000 mA transformer can support up to fifty lights of that size, but it can only support ten of those 100 mA bulbs.

Questions & Answers

This device can handle lights that require 6V 15mA?

Based on what I understand, that is the only type of lights that would be applicable to it.

Can I use my own power supply or will there be one that is proprietary? Can you tell me what the size of the male plug is on ?

This power supply can be used with any power supply, the PC board's purpose is to dial down the voltage from 12V down Regarding the plug, I am not familiar with it.

What's the best way to power this gadget using a plug in adapter?

According to specs, this can accept an AC or DC input of 4 to 24 volts. All you have to do is follow instructions as to how to proceed with hooking up. To provide you with the power pack that is used to run the trains on your layout, we are aiming to source it.

Do you need to change the resistor if you have led lights with pre-installed resisters?

The resistors had nothing to do with it

Selected User Reviews For PCB012 Power Distribution Board Self-Adapt Distributor HO N O LED Street Light Hub DC AC Voltage Train Power Control

I can use this to build LEDs for my train table street

5/5

In fact, this gadget is so versatile, I put it to use with a 12v adapter I had from a razor because it had the right size male plug to fit the port. I use the 12v setting, and it powered nearly 45 2 at that voltage. A distribution board that Evemodel sells has up to 14 lights on it, which is made up of 6V leds in series with one resistor per chain of 8 or more lights. Couldn't ask for a better day!.

Zakai Ray

| Dec 12, 2020

The light trans is on

5/5

My HO train set has many street lights that I love using this unit for. The installation and management are easy.

Zaiden PRITCHARD

| Jun 14, 2021

I bought two of them, none of them work

3/5

The design is beautiful, the workmanship is excellent, and the accessories are excellent. I thought I had a problem with either of my boards, but I don't. I am not ruling out the possibility that I am doing something wrong but when I put a voltage ohm meter to the output, it goes up to its rating, then falls off to 0. Lights an LED but not a single pixel. There was no way to power it despite numerous attempts. This board must work as advertised for it to be useful. Please help me!.

Bryson Ramsey

| May 14, 2021

This is not a good investment of your time and money

3/5

The products produced by Evemodel are terrible. This is yet another crappy product from Evemodel! The first time I used it, it didn't work. My power source had to be connected with a jumper straight to the distribution board in order to at least still operate the machine. Due to my location in Philippines, I do not have the ability to send the package back. I didn't want to spend more money, so I didn't The replacement process takes a great deal of time. This was an absolute waste of time and.

Xavier Tyler

| Nov 07, 2020

Lighted for the first time, and it went well

5/5

Lighting is being attached to a layout for the first time. Two of these are owned by me, one for white and the other Everything appears to be functioning as expected following the directions.

Memphis Huffman

| Mar 18, 2021

The power setting must be correct before the unit can be livened up

3/5

It's what I use for my train layout to illuminate the streets with LEDs. A big mistake I made was to put the switch in the wrong position and blow out all the street lights. In addition to that, I have several programs.

Ember Bradley

| Dec 03, 2020

Easy to do

5/5

That's great. My options are greater than the plug and play light system, since I can hook up more lights instead of just 4 like the woodland system.

Sara Schmidt

| Mar 20, 2021

Does the job

5/5

I used it on my train table to light up my lights. I am satisfied with the outcome.

Adley Frank

| Oct 08, 2020