KES Brass Shower Arm Diverter Valve Universal Bathroom Shower System Replacement Component for Handheld Shower Head and Fixed Shower Head Matt Black, PV14-BK

This diverter valve is sturdy and well-made. A valve of comparable quality from a company such as Delta would set you back four times as much as this one. To install a dual shower head system, I used the valve from my parents' master bathroom. It functions admirably. There have been no leaks. Made of high-quality brass, this item is significantly less expensive than similar items from other brands. The diverter allows you to switch between the main shower head, hand shower, or both at the same time. br>br>My only criticism of this diverter is that it should come with two female threaded ends, which would eliminate the need for a 1/2 female coupler, but that isn't a major flaw. It is certainly insufficient to launch a product at such a low cost that the quality far outweighs the cost. There is no need for a coupler if you install the diverter to the existing arm coming from the wall and attach your shower head directly to the male threaded in. But there were two reasons why I didn't want to use it that way. To begin with, if you use a large shower head, such as an 8-inch or larger rainfall shower head, the diverter will be difficult to reach because it will be located directly behind the shower head. In addition, I wanted the hand shower's hose to be as close to the wall as possible. As a result, I chose to replace my existing shower arm with a 4" straight nipple that protrudes from the wall. The female end of the diverter was then attached to that nipple, and I used a coupler on the male threaded end of the diverter to attach my main shower arm, which is where the main shower head is attached. This moves the diverter closer to the wall, allowing the hose from the hand shower to sit close to the wall while also hanging straight down at a 90-degree angle when not in use. Instead of being directly behind the shower head, it also makes the diverter easier to access. However, you'll need to buy a 1/2 female coupler if you go with this option. br>br> It should also be labeled with the direction of water flow. I had to learn the hard way by putting it on backwards and then having to disassemble everything to turn it around. It's not a huge deal, but it's worth noting for anyone considering buying this item. The water flows in the opposite direction from the female to the male end. It will work if the water flow is from the male to the female end, but only the main shower head or both shower heads will function in this configuration. The main shower head, the shower arm, or both can be used from the female end to the male end. So, basically, you'll connect the diverter valve's female end to the shower arm coming from the wall, ensuring that the water flow is directed in the proper direction for this device to work properly. Overall, this is a fantastic product.

Kole Peterson

| Dec 27, 2021

The shower head was taken out. I removed the old teflon tape from the arm's threads. To the threads on the arm, I applied new teflon tape. The shower head would not screw on to either of the threaded fittings after the diverter was installed perfectly fine on the arm, snug fit and lined up nicely. I began to doubt my own sanity at this point. My man card was valid and in good standing when I checked it. I removed the diverter to get a better look because I was still doubting my own sanity. Removed shower head from arm, installed diverter, diverter went on arm fine, checked showerhead to see if wife was playing a joke on me, removed shower head from arm again, installed diverter, diverter went on arm fine, removed shower head from arm again, diverter went on arm fine, removed shower head from arm again, diverter went on arm fine, removed shower head from arm again, diverter went on arm fine, removed shower head from arm again, diverter went on arm fine The shower head does not screw into the diverter in the correct location, nor does the hose for the detachable shower head. I can't get the threads on the diverter to start because they're the wrong pitch. br>br>Remember, I said I double-checked this: the head screws on and off the arm fine, the diverter screws on and off the arm fine, but the hose and shower head do not. This must be a machining error or a bad batch, so I'll try to return it and order another, and I'll keep you updated. I was dissatisfied with the level of quality control here. I mean, in the United States, isn't NPT 1/2" the industry standard for shower heads? 3 days later, br>br>Edit: It got even worse with the replacement. The female threads that attach to the arm are machined incorrectly, so the outlet for the handheld showerhead is pointing up, not to the side; I can't snug it down, and if I loosen it, it leaks; the threads are different than the showerhead and don't fit the same as the first; and the female threads that attach to the arm are machined incorrectly, so the outlet for the handheld showerhead is pointing up, not to the side; I can't snug it What a waste of time it is to waste time on this nonsense. I guess the people who left positive reviews had better luck than I did.

Ocean Hobbs

| Sep 26, 2021

Our old diverter was difficult for my wife to use because the valve had to be pulled in. out to change the water flow, which required a great deal of force to accomplish. As a result, we desired one that was simpler to operate. The water flow direction can be changed with very little effort by rotating the valve in this unit. It is a big hit with my wife. It's a well-made piece of equipment that should last for years. A small roll of Teflon tape was included as well. br>On the other hand, there is one drawback: On the part of my old diverter that connected it to the main water supply pipe, there was a nut - As a result, while tightening the nut to secure the connection, you could hold the diverter in the desired orientation. That feature is not available on this KES unit. As a result, tightening the connection requires turning the entire unit, and you may end up with a tight connection but a diverter positioned in an undesirable orientation. I ended up with the valve handle on the right side of my shower head instead of the left, which I preferred.

Remy Gallegos

| Feb 19, 2021

The only reason I didn't give this diverter a full star is because it's entirely made of heavy metal. The arm rotates smoothly as it performs its function. The design, on the other hand, is where it falls short. The water must pass through two small holes, causing a flow restriction that will be obvious. Unless you want to get out a drill, there's no way to get rid of the restriction. I sent a message to the seller, inquiring about the flow restriction, but received no reply. It's all over again - The item has never been used and is still in its original packaging.

Eleanor Castillo

| Jan 23, 2021