Moen 11985 Replacement Pivot Rod for 50/50 Bathroom Drain Assembly
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
There are no part numbers on the package. My Asceri (Moen #76515) 2 handle widespread bathroom faucet does use this device as a replacement part.
The point is well made by Sig. There should be a 3/4 instead of 3/4. There is an inch of nut on the bolt.
We appreciate your interest in our products and wish you well. With this Moen 11985 Replacement Pivot Rod for 50/50 Bathroom Drain Assembly you get the plastic wing nut designed to fit Please feel free to call us at 800-878-7758 with any questions you may have The number 289-300 As of today, Monday through Friday from 9am to 5pm, we can be reached. The hours are from 600 am to 700 pm It is 30 minutes past Noon
With this, you can use any Moen pop-up faucet You have to go up the If you find any damage to the parts, take them off and compare them with the illustrated ones to ensure that yours is a "standard" pop-up. You can type up.
Selected User Reviews For Moen 11985 Replacement Pivot Rod for 50/50 Bathroom Drain Assembly
I could not find this product in my local big box store, but it was a perfect replacement for what I was already using. In this case, even though the 11985 is a replacement, If there is a 14606 stamped on your grey screw attachment, it will still work.
As far as my faucet was concerned, it worked just fine except for (2) I had to use the old plastic nut since I had to cut about 1/4 inch off the short end. While I did not use the metal washer, I did use My faucet does not have a brand name on it, but I think it was from Over 10 years old, the item might be Glacier Bay from Home Depot, which is an older brand. This short end measured 1 1/4 inches in length when it was delivered. A ball of this size is the same as what I had before. It is important that the manufacturers of these items specify the complete dimensions Luckily, I only had to trim the short side with a hacksaw to get it to work. A good way to measure the required length is to add a wooden coffee stirrer and mark where the thread begins in a pencil. After that, make it a little shorter so that it can accommodate the ball and leave a little space.
Typically the rod tip rusts off and the rod has to be replaced. The moen replacement comes in generic form but it is the same product. However, this replacement kit does not include an essential part, so it gets a lower rating because it is well made and installation is not overly difficult. There is a small clip that attaches the rod to the carabiner. You can use the old one if it's still in use or you can purchase the new Despite their universality, these clips may not work on all computers. Depending on the size of the rod, they come in different sizes.
I feel like maybe $10+ was too much for a metal rod squeezed into a plastic ball, especially since the item it replaces is just As a matter of fact, the old one didn't As if by magic, it shattered into She had been pulling a wookie out of the drain when the shaft broke. The kind of cheap chrome you're talking about Are you more prone to breaking than bending when the plating is brittle? Could it have been too slowly annealed? *nod* Well, whatever the case may be, this replacement rod was the My sink stopper now works like new after installing it in less than five minutes. My only problem is the fact that this rod alone cost roughly the same as the entire assembly, which includes.
As I was doing a little maintenance in my daughter's bathroom after she had left home and we made her old room a guest room, it occurred to me that the sink drain was not functioning. After removing the old mechanism, I discovered that the shaft that raises and lowers the drain plug was corroded to the point of being useless. It's quite likely that this is the result of whatever facial chemicals or other items she washed down the drain, since a similar faucet in a different bathroom was still in very good shape. No matter how I looked at it on Amazon, the part looked just like the old part, which I found to be an exact replacement, even though it had no part numbers. It was a very easy repair and it will keep the faucet draining for a very long time.
The rusted ball rod can be easily replaced by these simple, easy replacements. Designed for direct replacement of Moen. I guess, after all these years, there is a better way to attach the stopper than what we have been using!.
The new one works perfectly and it only took 5 minutes to replace the A replacement like this can easily be handled by anyone. Earlier this year I received a lifetime guarantee on a Moen kitchen faucet that I used for a few years. I could have gotten this for free if I had contacted Moen. I found this on Amazon and I have prime, so I got it in one day, and I'd have to wait longer if I were to order on Moen. No one in either box store had this product in stock nearby. When I noticed later that I could have simply placed the ball at the other end, about 1 3/8" or so, and reused it with the old rusted end, I did.
Replace your rusted one with this We didn't need the pivoting washer because the old one was still intact. It was a very easy repair, that took less than 5 minutes to complete. The product worked so well that I had to order another 2 for the In an update, I just replaced 3 of these on Moen faucets. They work great and I later discovered that I could have gotten them all for free through Moen. New aerators will be delivered to my home in the next week after I make the call. Oh well, live and learn. Oh well, I should have called Moen first.