HBT HBCN65P 15 Degree Coil Siding Nailer with Magnesium Housing, 1-1/4-Inch to 2-1/2-Inch Plastic/Wire Collated Coil Siding Nails
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
There will be no change in that. There will be a jam in the gun if you use roofing nails
The works I use hold 6 gallons of water and I've never had any
The device is equipped with a type D air nipple. Typically, that is the size of the most common
The nailer jammed all the time, so I returned it. In stead of returning this nailer, I invested more money in a Bosch siding nailer which I am extremely
Selected User Reviews For HBT HBCN65P 15 Degree Coil Siding Nailer with Magnesium Housing, 1-1/4-Inch to 2-1/2-Inch Plastic/Wire Collated Coil Siding Nails
people, I live in the real world and don't live in a fantasy world Unlike the more expensive guns, these guns will not perform like the name brand guns. This helps me install Hardi Plank siding and other siding products I have found this product to be reasonable for the price. Easy to load, easy to unjam, which has only happened twice so far I, & The nails were all merely a few tacks long in both cases. When there are fewer than 20 nails left in the coil, I change it. It works fine as long as you keep it oiled, use the right pressure, and do not drop the ball. You should have no problems with it unless you use it every day for many hours When using a gun, you should use one of a higher quality. There's a saying that says in the real world you get what you pay for, but if you're prudent & watchful you'll be okay Adapt your tools to your needs. You can get by just fine with lower priced tools if you're diligent A $100 gun cannot be expected to be as good as a $300 gun.
We replaced 353 feet of board on board picket fence with this method over four weekends. I was able to use both 2" and 2 1/2" 15 degree nail rolls with no problem. Air pressure around 100 psi is used with a pancake air compressor. I absolutely loved this gun and it performed flawlessly as well. In contrast, I wonder how a $450 gun would function or compare, but thankfully, I did not have to find out.
In my case, Hardie plank was causing multiple problems to be caused by a framing nailer. Due to the low price and the fact that I had limited work to do, I picked up this one, and it has affected my life The first thing I noticed was that it is easily adjusted, so I did not have many As a result, it is lighter, and I don't have to constantly reload it. Working with it is much more fun, and I think it's going They can be found for much less than 2" framing nails and are easier to find. As an added bonus, the case helps me transport the product in my vehicle more easily. Some of the plastic parts were a concern but after using it for a couple of weeks I am happy with it. It has a nice size and balance in comparison I would buy from this seller again and recommend it to others.
Heavy but not too much. Setting depth in response to the user's needs. I was happy with the price and the gun was nice. I've been working here as a carpenter for more than 10 years. There was no problem so far on the one LP SMARTSIDE installation that we used it. It was also liked by the carpenter leading the job. It worked great when I attached a wide hitachi hook to it. However, you should be careful Anything at all It is believed that color combinations such as black and yellow (the color of bees) will attract bees.
After receiving my coil nailer for a cement plank siding project on my house, I encountered several jams during the first few hours of use, which wasn't ideal, but I figured you get what you pay It has run without a hitch for the next three weekends, until the project was completed. There is only one complaint I have -- a ladder hook on the wall would have been nice.
This is a very good As I finish nailing into dense pine through Hardie, I find it to be holding nearly all the way (about 1 in 50, 2 3/8 bend upon nailing into dense pine). You need to touch it lightly. All you have to do is press the trigger while it's pointing at the surface of the work area. There you have it. My guess is that there would be very few misses if I were to use smooth shank galvanized nails. It is a great tool, and I would definitely buy it.
There is nothing good about this nailer. There were a couple of double nails, and I was not able to get a full coil of nails through it, and it jammed up and wouldn't This was a waste of time, effort, The quality of the product is determined by the price. I think it may have been an off day. It appears they are no longer available at this time, This is not a good idea.
This is not the case when it jambs. The good news is that it works when it should. It's not great when it jambs, but when it works, it's great. Watch out for the nail head depth, as it varies from week to week. I had to send back the first one, another brand lasted about ten It's really good to have a The siding used for Hardie cement is composed of this material.