GRR-RIPPER 3D Pushblock for Table Saws, Router Tables, Band Saws, and Jointers by MICROJIG
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
It is entirely dependent on your intended use. I bought the 100 and it worked perfectly, so I went ahead and bought the 1/8" leg to do some thin ripping. Although I did cut into a portion of the leg, this has been helpful. It was my fault for not applying enough force against the fence with the gripper. After that, I purchased the piece that converted the 100 to the 200. Overall, I overpaid because I was trying to save a few dollars. Today, I noticed that Amazon is offering the 200 with the 1/8" leg for $79. If I had to do it all over again, I'd choose that option. I hope this has been of assistance.
I'll keep my blade guard, thanks. The above response is more Gripper propaganda. Lawyers did not design blade guards to be useless impediments. My blade guard has prevented a number of mishaps and is clear enough for me to see the kerf.
The GRR's second leg Because RIPPER's thickness is just under 1/4", it can cut 1/4" thick strips right out of the box. We also sell a 1/8" leg as an add-on that allows you to cut strips as thin as 1/8". Just keep in mind that when cutting thin strips, you should always use a Zero Clearance Insert to ensure that your thin strip does not fall into the blade or riving knife openings.
It's simple: just lean the Gripper against the fence and lower your piece. After that, loosen the thumb screws and allow the support to fall to the table.
Selected User Reviews For GRR-RIPPER 3D Pushblock for Table Saws, Router Tables, Band Saws, and Jointers by MICROJIG
This is a product that appears to be so basic that it isn't worth the money, but I can assure you that the reviews are accurate. It's difficult to fully appreciate something without holding it in your hands, and I was skeptical right up until the first cut, when I realized. whoa. It's not just a push stick with a lot of extra features. It's a jig for cutting with safety features built in. br>br>The price is high, and I was skeptical at first, but the value is undeniable. Furthermore, it outperforms all of the other tools in the arsenal by replacing the blade guard, feather board and push stick together. It allows you to maintain complete control over the work piece throughout the cut, allowing you to make cuts that would otherwise be too dangerous – with complete confidence. Your cuts will be more precise as a result of this control. That's not even taking into account its router table and jointer applications. br>br>That's a lot of value for a simple little plastic gizmo. Sure, it's over-br>br> priced. But, in my opinion, the creators of this item have made a profit. They've made a simple tool that makes a potentially dangerous task far safer. A second one is on the way. I figure it'll be worth it to save my fingers.
I had high hopes for this product because I needed thirty 14-inch-long, 3/4-inch-wide strips of 1/2-inch walnut. The gripping surface remained tight throughout the first cut, resulting in a clean cut. However, because sawdust adhered to the green surface, it slipped, and I lost control of the second and subsequent cuts; after four or five cuts, it was unable to push the wood through the cut, resulting in a potentially dangerous situation with the wood halfway through the cut. To use this tool, you must first remove the guard and splitter from the saw. Any miss- The wood will be twisted sideways into the blade as a result of the applied pressure. Another potential hazard. To finish the job, I had to resort to using feather boards and push sticks.
I've been attempting to create wood veneer for my wall. This appeared to be a convenient way to keep my fingers from being severed while using my bandsaw. I gave this product three stars because I still have all of my fingers, which I believe is worth at least three stars. However, I deducted two stars because it didn't appear to be worth the exorbitant price I paid. I ended up returning the item because I could have achieved the same results by simply adding rubber to a wood block. As I used this product, I became increasingly frustrated because the rubber's grip became weaker. To keep the rubber from losing its grip, I had to rinse it with water after each cut. br>br>On a side note, the assembly instructions are inaccurate for those of you who decide to buy this. They say you'll need two washers, which aren't included in the package. However, there is a small card that isn't included with the assembly instructions that explains how the parts have changed and shows you how to put it together.
Doesn't do a good job of gripping wood, to be honest! To keep it from slipping on your work, you'll need to apply a tremendous amount of force. It becomes increasingly dangerous for me, and I prefer to use my hands instead. I tried it on a piece that needed a flush trim on the router table, and it was a disaster. I couldn't get my piece to move around for some reason. This is a ridiculously stupid device. br>br>NOTE: THIS PAGE HAS BEEN UPDATED. The key to this is that the bottom gets dusty, but if you clean it off with alcohol or water, you can reclaim your incredible holding power. It's something I use all of the time now.
br>I am a seasoned woodworker who uses this product with a full-size 10" cabinet table saw for furniture and cabinetry, not cigar boxes or the like. br>br>The marketing for this product is extensive, claiming to be THE go-to push block for any operation on the tablesaw (and other woodworking machines). Advantages: br>br> br>Well-made, with no sharp edges or other flaws. br>Perfect for small pieces of wood. br>br>Contrary to popular belief, there are a number of disadvantages to using this product. br>Expensive for what it is, and every "extra" that should be standard adds to the price. br>You can't use the standard blade guard with this block. br>As soon as the wood is wider than 3 inches, the blade is exposed. Between the fence and the push block, they recommend placing a spacer block. It's far too time-consuming and fiddly to do. br>Does not provide any positive feedback control, despite what videos claim. The use of fence rollers, standard safety guards, and other similar devices prevents the wood from being thrown back at the user. br>If the wood is longer than 18 inches, you'll need two blocks, and even that will be difficult. br>br>My recommendation is to use a featherboard, either homemade or purchased, as well as a combination of a push stick and an old-fashioned push block. br>It's safer and more likely that the board will not pull away from the fence. Fingers are a little further away from the blade this time. br>Each cut is unique, e. g. This can be used to push/guide wood in a variety of ways, such as through cut or not, size, and so on. It is not the ONLY tool that you should employ.
Update: I had to purchase a second one because I enjoyed it so much. br>br>Let's be honest, this is a lot of money for what it is; however, a stop saw can cost thousands of dollars, and this is the next best thing. I've never felt more secure in the shop than when I'm using the tablesaw, which is one of the most dangerous tools there is. Take a look at the image to see how you can make toothpicks that are 1/4 by 1/4 inch. This could not be done with any other push stick on the planet. The 1/8 inch leg was the only attachment I purchased. That works incredibly well! br>br>It'll be well worth it if this review saves just one person's finger. Please purchase; it is the best and most secure option available. br>br>I would absolutely recommend this product, and I am in the process of purchasing a second one. I wish I could give it a perfect score of ten!br>br>I hope this information was useful.
I must admit that when I was watching various woodworking channels on YouTube, I did not believe this product would work as easily as it appeared. This is the first push block I've bought (I'm a new woodworker), and I'm very pleased with it. You'll need to set aside some time for assembly, but once you start using it, it'll be a complete afterthought. Clean, precise, and straight cuts are made.
Related Products For GRR-RIPPER 3D Pushblock for Table Saws, Router Tables, Band Saws, and Jointers by MICROJIG
