Amana Tool - (54314) 3-Piece Carbide Tipped Tambour Door/Appliance Garage Door 1/2 Inch Shank Set U.S. Patent No. 7 810 532
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
The 1/4" shank version of this product is not available.
The minimum radius for a tambour door is 3 inches Half an inch. The length of a table should not exceed 5ft or 60in, as otherwise it might sag under its
I made a couple of mistakes so I made extras. You will need at least 14, but I made extras because I miscounted. It was a great product for me, and I would certainly recommend it to others. It is very important to carefully read and follow the instructions.
Selected User Reviews For Amana Tool - (54314) 3-Piece Carbide Tipped Tambour Door/Appliance Garage Door 1/2 Inch Shank Set U.S. Patent No. 7 810 532
A roundtable discussion was held about We do not need an over bit. In its place, they should put the 9/16th bit. In my opinion, the round-robin system should be used It is probably an older left over from a previous version of the This is why I gave it There is more to it than you think you need. To build the bed, I used 21 double slats (i. e. 68 cm) of the final 41 tambours. It probably could have been done with a few fewer. With each final tambour (after cutting the "double"), you get roughly 17mm of It is almost certain that you will make some mistakes. Don't be afraid to During the setup, be patient and take your time to center the bits. However, there is not a lot of wiggle room in the setup. Follow the pointer and make sure the height of the bit is just high enough for the bit's bottom to barely touch I am not sure if making two passes is necessary. Using a double height feather board, and one from the top and one after the bit, I used one from the top and one after. A 43-inch TV is covered by this. It is my first attempt at making this kind of thing. I am so pleased with the final result, and it worked out beautifully. It won't be so fast, easy, and quick as you may think. I mean don't underestimate the power of the dark side. Even so, the effort was worthwhile.
It was purchased through Amazon by a seller who provided excellent service. It is a great bit set! Also included is a detailed step-by-step guide to building a bread box with tambours. However, there are a few grammatical errors and some pictures/drawings that need to be corrected. There is even a joke about Lonnie Bird in there. During his description, he mentions that this is a fun weekend project. However, he does not specify that it A router table is an essential tool and you'll need to practice quite a bit before you can cut tambour slats properly, but they work well when done In addition, you will need a 9/16" dado bit (that Amana will sell you) for the slot in which the tambours slide. You will also need to build two Also, you'll need to glue up some panels and mill the edges into thin sections. When it comes to bit sets, I advise buying them all as one since you really need all of them. We had a lot of fun with the This is great!.
This is well worth the money,.
Brands that need to be sharpened usually need to be done. This is a bit of a hassle The bit wasn't perfect, but it was nice. I usually have to have them sharpened when new, but these were extremely sharp and very robust. There is a really nice bit of double tambour in this bit. Material to work with is very smooth and there are plenty of pieces to work with.
I think it is too expensive for what you get. A little over three inches is when the bit broke.
A tambour door bit set like this is the best that you can find All three bits cut perfectly smooth profiles the first time and the one hundred fifty times the same. The fabric no longer needs to be glued down or wires drilled through to connect them. Assembling the parts of this set is easy, and the results are absolutely beautiful. tambour fabric doors always get stuck or out of line when they are converted to roll-top doors. The roll top door was lovely and worked beautifully. I have only one complaint about this whole thing -- not thinking of it first.
I highly recommend the Amana tambour door bit set to anyone who wishes he could have a roll top door but doesn't want to deal with the hassle of installing one. I did not have any trouble with this one.
I received the item in good condition and in a timely manner.
If you don't want to glue canvas on, this is a good substitute.