ANEX Ultra Low Profile Offset Ratcheting Screwdriver 90 Degree For Tight Area (Magnetic 2 Bits Set) Downwards Angled Head, Blue

The first time I installed grab bars, due to my inexperience, I created a very nice install job, but I forgot to put two screws directly under the grab bar bend, where the bar bends to meet the end plate that connects So there I was with two screws that were unsecured and a really tight fit. Because of the low profile, as well as the great reviews, I decided to purchase the Anex 425 Low Profile Hex Bit Ratchet. It arrived as described on Amazon, and I immediately used it to tighten two Phillip screws in a confined space, one at each end, and secure grab bars without removing the bars and drilling new holes in the ceramic tile. It worked as advertised, and I would highly recommend it.

Elianna Whitehead

| Oct 16, 2020

There were quite a few different small ratchets I tried. There is no comparison to this one. If I had the option, I'd rate it 6 stars. The following are the comparisons Doesn't it look like a little pinion? By turning it with your thumb and forefinger, you are able to tighten the fastener until it is tight enough to A ratchet is useless until there is some resistance to push against. In every other case, either the fastener needs to be turned all the way or another hand needs to be used to keep it from turning backward- Continuity is key. As a result, it is often impossible to maneuver in tight spaces. In fact, the whole point of these tools is that they allow you to work in tight spaces! Moreover, the forward/reverse mechanism is sturdy and does not accidentally flip back The other products either use flimsy switches that flip easily, or they have a rocker that's right beneath your fingertips This results in you flipping it by mistake all the time. A real pain in the neck. It is crucial for my projects that I have an Anex, as I have to screw and unscrew a lot in tight spaces. I have three of these, and another one that To make things easier, I keep my four Anex tools stocked with a variety of different Allen keys for various socket sizes I'm most familiar with. The first one I used for over a year has been good to me. The quality is fantastic and there are no issues after all these months. I've been applying a lot of force sometimes as well. The structure of this small car is impressive considering its size. The last point. It is built in Japan, and the quality is evident.

Lyric Sampson

| Dec 28, 2020

already have a comprehensive bit set for general house repairs, but I like this one because it should fit inside the bit set just in case I need something low-profile or something that I could grab and go when I need it. Here we go. There's no doubt this tool is well made and of a perfect size, shape, and magnetism. It looks better made than the similar tool I saw in the picture. The dimensions are great for my purpose, and will likely be a great fit for the tight spaces I have. I plan to get both upward and downward angled Brothers in the series now that I know the quality.

Maya Durham

| Jan 23, 2021

It is not a samurai sword, but it feels good in your hands considering it costs less than Ratcheting is effortless with the L R switch, which is positively and smoothly operated. In comparison to a drill adapter, the magnet could be considered a bit weak. However, I have never used a tool such as this before, so I am not all that familiar with this. It fits a sensor under the firewall under my truck that is hard to reach using.

Patrick Massey

| Jun 17, 2021

The bolts on most, if not all, of the chairs were loose, making the chairs Despite its small size, this little ratchet proved to be very useful! To tighten and loosen the bolts, it's just small enough to fit into the access grooves. This is a very good value for money. It also seems to be very well made and made with There's only one reason I gave it 4 stars, and that is because it's edges are a little too "sharp" and depending on how you hold it, you may end up cutting Overall, it's a great little ratchet that's useful and handy. It's not a deal breaker but I would have given it 5 stars if the edges had been smoother to make it feel more comfortable in the hand. A magnetic bit holder is another thing I really like!.

Henry Prince

| Sep 23, 2020

Craftsman is better than this. When I first purchased this, it was made by Craftsman for Sears There are two different angles on each bar, you can take one for $10, or you can get three for $22. I have two problems with them Among the reasons for the lack of a magnet in this engine (a) it doesn't hold the bit it falls out with a slight tap and (b) the vinyl pad would slip from the bar once it was firmly attached to the top. The vaunted Made-in-USA has gone out the window There is a USA label on the bottle. introduced its Z-Series a couple of weeks ago. Quite a bit better magnet than it's predecessor -- $14 standard, The solution attached to this product does not suffer from either It is impossible for the pads to fall A solid, heavy build with beveled edges feels solid and well-finished. There is a smooth feel to the ratchet. There are no partial rivets, they are all in These are the colors as they appear in the photo of the product. It may also fit into smaller spaces since it is a little skinner. My only complaint about the magnet is that I'd prefer to have a stronger one. This "Made in Japan" product ships from Japan in a couple of weeks, but the shipping and delivery ETA is promptly provided. I would like to let Amazon know There is some confusion about why "China" appears in some versions of the product description (attached is a screenshot).

Jamie McFarland

| Apr 02, 2021

In order to use it, I bought a General ricocheting offset screwdriver a few years back. While it was not a very useful tool and was not effective in getting into tight spaces for screwing in screws, I continued to use it since I did not have any other screwdrivers that allowed me to reach tight spaces. In the end, I ended up purchasing this one after getting sick and tired of this terrible tool. In comparison to my expectations, I was disappointed. When I went to screw a wooden screw into place, I was amazed to find this was a very good tool and was rock solid for The tool is well made and inexpensive, so I have no hesitation in recommending it.

Rosalyn Irwin

| Nov 14, 2020

As someone who just went through an automotive repair that was far more challenging than it needed to be because you did not have a close friend to help out, I experienced the same trouble. A ratcheting tool with quarters. A Neiko one caught my eye, but it looked a little cheap and I didn't need the extra features. I like that it is very solid and that the ratchet mechanism works well.

Kehlani Mills

| Feb 08, 2021