Magswitch MagJig 95 Magnetic Woodworking and Welding Base Clamp Holder for Wood Working Supplies, Accessories, Tools and Equipment, Magnet Switch with On/Off Capabilities, 95 lb Holding Force, Yellow
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Yes, it's made of metal. The wings have small holes in them so that they can be screwed to the jig.
Yes and no are both correct. Because they're not electronic, they'll keep working even if submerged. However, because they are a mechanical device made primarily of steel, they will rust if exposed to moisture for an extended period of time.
A small column of powerful magnets can be found inside. When the column is in the "ON" position, the poles (opposing pulling forces) on the same side are aligned, creating a unified pulling force. When the switch is in the "OFF" position, the top magnet in the column rotates 180 degrees, preventing the poles from cooperating.
Rare- Earth magnets are permanent magnets that lose all of their force when heated above their Curie temperature, which is greater than 300 degrees Celsius. They also have a working temperature at which they begin to lose force permanently, which is around 80 degrees Celsius. Over time, they'll lose a tiny fraction of their force( ten years) As a result, don't let them get too hot to handle.
Selected User Reviews For Magswitch MagJig 95 Magnetic Woodworking and Welding Base Clamp Holder for Wood Working Supplies, Accessories, Tools and Equipment, Magnet Switch with On/Off Capabilities, 95 lb Holding Force, Yellow
Colin Knecht suggested putting a piece of rubberized kitchen cabinet liner under the magnets to prevent them from moving once they've locked. I haven't done so yet, but if the need arises, I will. The magnets are extremely powerful in and of themselves. I'm always on the lookout for new ways to put these fantastic items to use.
The MagJig 95/10 is a better name for it. Do you think these are strong? Yes. very. However, there is only one way to do it. And you're standing over it, attempting to lift it from the metal table. They're flimsy, so they're putting pressure on it from the side. Even with two built into a single jig, they slide fairly easily. This is the last thing you want with any type of jig if you want it to be accurate. Consider how the fence on your table saw slides as you cut a piece of wood. I wasn't building a table saw fence, by the way. I was merely attempting to provide you with a visual aid. We use jigs for almost everything we make. When using tools, it is necessary to be extremely stationary, which is why Tslots and fences are used. This is done to prevent things from moving from side to side, and to ensure that no one tries to lift their fence into the air. We're attempting to prevent the situation from deteriorating. Having said all of that. . . This isn't going to stick around for long. nope. Even with two of these in a single jig, it's not going to be enough. I only gave it two stars because I believe the marketing strategy is somewhat deceptive. This should probably be renamed the 95/10 MagJig. There is a downward force of 95 pounds and a lateral force of 10 pounds.
I purchased three of these to use as table saw jigs. Imagine my disappointment when they failed to hold. Because my jobsite table saw is made of aluminum rather than steel, magnets will not stick to it. The good news is that one of my friends owns a body shop and uses them frequently to secure welding blankets. He grabbed them all and went out to buy me a steak dinner.
These were purchased to secure a router fence for a router table that I installed at the end of my table saw. These are used by the fence to keep itself in place, both vertically and horizontally. br>br>The vertical strength of the 150 and 95 has been well documented. That's a downward force of 150 pounds and 95 pounds, respectively. The fence base appeared to be a lever for raising the magnet, so I assumed it was. So I calculated how much hold I had by multiplying the distance between the magnet and the router bit by 150 lbs. Based on that, I added a second magnet, and everything was fine. The shear or horizontal holding force, on the other hand, was not so obvious. It weighs 27 lbs for the 150 and 15 lbs for the 95, but the weight varies depending on the thickness of the metal you're attaching it to and the composition. Visit their website and read the technical specifications for more information. I had a maximum shear resistance of 54 lbs with two magnets. However, because my table saw is well-lubricated, this is minimized. I still have about 35 pounds of shear resistance, which appears to be sufficient. Fortunately, I use Jessem Precision Rollers, so the piece's force against the fence is generated by the fence, and I don't require as much shear resistance. It is possible that your results will differ. Just something to consider if you're going to use it in this manner. br>br>Instead of using a 40mm forstner bit, I created custom holes to hold the magswitch base's unique shape. The starting point is a fraction of a pound. I used the appropriate bits to make two start holes that were 25" wide. After that, it was just a matter of jigsawing and filing it to fit. It was a little loose at first, but once it was screwed in, it worked perfectly. br>br>Overall, these are fantastic. Just make sure you're aware of the specifics to avoid disappointment.
Your holding results will vary greatly because you are a magnet. The type and thickness of steel will determine the holding strength. br>This thing will be useless if it is made of stainless steel or aluminum. The holding force is only about 10 lbs when attached to the thinner steel of a filing cabinet, for example. It took about 30 pounds of straight pulling force to get it off my bench vise anvil when it was attached. Although it has a good grip, it is insufficient for the intended purpose. br>However, when it was attached to a plain steel door hinge, I had to yank it off with all my might. The sliding force was also quite strong, probably around 20 lbs, if not more. Enough to prevent a jig from moving, especially when two magnets are used. br>Obviously, the steel type matters, as I thought removing the very thick bench vise would be impossible, but it turned out to be a door hinge. I'll update the review once I've put it through its paces on the drill press and table saw, where it belongs. I'm hoping it's made of the same steel as the door hinge.
This is what I use to hold jigs to a metal top while running wood through 4500 RPM sharp blades. It performs admirably. You understand that the power line runs from the knob to the bottom. On the sides, there isn't much. You'll also need a substantial amount of metal to attach to. br>br> Example: Place this on the refrigerator's side and pull it straight off. Holding a 15-pound weight is a possibility. A thin sheet of ferrous metal is attached to the outside of the refrigerator; place it on a steel 1-inch plate. With a crowbar, you can't get it off the third block (I tried). br>br>Excellent product, but you must first comprehend what it does and how it functions.
I purchased a set of these to use as a jig for my table saw, and they worked so well that I purchased a few more. br>This time, instead of screwing them to the jigs, I'm going to build several jigs and then just cutting the holes pretty snug for these to fit through, so I can mount the jig to a saw, use it, and if I need to use a different jig, I just pull these off the first one and put them on the second. This saves a lot of money. br>br>They're simple to use. br>They're very strong and keep my jigs in place. br>They can be used on multiple jigs to save money.
Related Products For Magswitch MagJig 95 Magnetic Woodworking and Welding Base Clamp Holder for Wood Working Supplies, Accessories, Tools and Equipment, Magnet Switch with On/Off Capabilities, 95 lb Holding Force, Yellow
