CISNO Dc 12v 10w-200w Transformer Power Supply Driver Led Light Waterproof Ip67 (15 Watts)

CISNO Dc 12v 10w-200w Transformer Power Supply Driver Led Light Waterproof Ip67 (15 Watts)

$ 13.99

Score By Feature

Based on 70 ratings

Easy to install

7.70

Value for money

6.69

OveReview Final Score

How Our Score Is Calculated

Product Description

A waterproof rating of IP67 is required

Other Electronic products that use a DC 12V power supply are also suitable for this power supply

This LED light is compatible with LED lights (3528, 5050, 5630 and so on) that require an AC 12V supply

We highly recommend that you check the input voltage before you buy it When purchasing the switch, please make sure that your power is less than or equal to the rated power supply, otherwise the switch may burn. If you are not sure about the power supply, please contact us.

Questions & Answers

"Cisno dc 12v 10w- 24" is the title of this product What does "200w transformer power supply driver led light waterproof ip67 (15 watts)" mean?

The current rating is 25 amps. This heading implies a power range of 15 to 200 watts for some reason.

My goal is to use two leds11. I need a driver to do this. Is it possible to run four fv 1000 ma at the same time?

FV is an abbreviation that I am not familiar with. If you are referring to direct current voltage, then you are talking about DC voltage. A 12 volt unit with this power supply will run at 15 Watts, or 1250ma. One of these units is needed for every 1000ma bulb, or you can use a single unit with about 30 watts to run two

Can you tell me which one would be best for 10 3W LEDs?

If there are multiple lights, the power supply wattage should be equal to or greater than the sum of all of them.

The stove exhaust fan is being replaced with two 6w leds in place of two 35w halogen bulbs. What are the chances of this transformer working? Transformers with halogen light always operate with leds. ?

There is no way I can tell you. Lamps can be measured by their wattage so you will know how much energy they require. There's no mention of what voltage the connection to the lamp has. Is there a way for you to find out what voltage the original 35 watt halogen lamps run on? Are these lamps going to be connected to a transformer? Can you tell me what voltage you want the leds Do you know if the circuit includes a dimmer? Depending on whether your existing lighting circuit is wired for 110 volts and the existing lamps use a normal connection, such as a screw-in connector, you might be able to simply find a replacement led lamp that screw in.

Selected User Reviews For CISNO Dc 12v 10w-200w Transformer Power Supply Driver Led Light Waterproof Ip67 (15 Watts)

The program seems to be doing its Rather than the 15W version, I got the 10W version

5/5

I like the way it works! I had expected a bigger kit, but it was smaller than I expected. I had to figure out the two black wires on the N/L side first, but that was all. There are basically two wires N is for the neutral, and L is for the live (hot). I noticed that you blink my LEDs once after turning off the power. It appears that the lights are dissipating any stored energy. I'm just pointing that out because it's not that big of a deal. In addition, the wires were a little thin for my taste, so it was a bit difficult to use them with wire nuts. For the last week I have had this and it has been holding up well. If it fails, I will update the review.

Gabriella Vaughan

| Dec 22, 2020

I lasted nearly 6 months before it blew up

3/5

I am consuming eight watts of power). To determine what caused it to fail, I opened it up to have a look and cleaned off the ceramic and silicon. On the first pic, you can clearly see how the 8-pin DIP IC is burned out, and on the second, you can see the cracked IC case. The experiment fails.

Carmelo Levine

| Jul 14, 2020

It is suitable only for LED bulbs, not for My only rating is a 3, as it did not meet my needs and was not strong enough to handle 20 watt halogen lamps

3/5

LED bulbs with a low wattage may be okay. This may not be the best choice for enclosed areas.

Braxton Hartman

| Oct 31, 2020

Replace the power supply for the halogen bulbs

5/5

I bought this power supply for my 6-inch tv a few years ago When I replaced a halogen overhead light bulb with LED bulbs, the LED bulbs would not light up. This was due to the original power supply having a power rating that was too high. I found this supply to be the perfect solution to my problem.

Alonso Murray

| Jul 30, 2020

That's not my cup of tea

3/5

Definitely not what I was looking for. The installation did not work for me, so I am unsure whether it worked or not. There was the same hole on the other side where the black wires came from, so it was difficult to figure out how they came together. I returned it to the seller.

Bonnie SYKES

| Aug 08, 2020

The stove exhaust fan doesn't work with LED lights in place of halogen light bulbs

3/5

Converting halogen lights to LEDs on a stove exhaust fan does not work, even though specifications are.

Van Santana

| Nov 13, 2020

The value of the product is good and it works well

5/5

Having only used it a short time, I cannot comment on its effectiveness I am able to power an LED tape strip with it without any problems. Despite the fact that heavy appliances, such as a toaster, operate at constant voltage, the voltage stays constant. The screen does not flicker. It has been a great experience for me.