Premium Heavy-Duty Shelf Brackets - Quarter Inch (1/4") Thick w/Lip - Rustic Black Iron Finish - Modern Farmhouse Industrial Open Shelving Holder Hanger + Hardware, 4-PK - Multiple Sizes (7.25")
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Restocks will be available by the end of June for all sizes.
As far as mounting the bracket to the glass is concerned, you will not be able to do so, but to our wood we did not actually use screws Since the shelf material cannot move since the bracket has a lip, we have not had any problems with it. It's amazing how well our brackets and shelves fit together!
I am using a bracket with a width of 1 1/2 inches
The box needs to be brought to a UPS STORE after Amazon has provided a return code. On the Amazon website, go to your order.
Selected User Reviews For Premium Heavy-Duty Shelf Brackets - Quarter Inch (1/4") Thick w/Lip - Rustic Black Iron Finish - Modern Farmhouse Industrial Open Shelving Holder Hanger + Hardware, 4-PK - Multiple Sizes (7.25")
This is not a cheap product! It's great to see brackets like this! This is a very sturdy and well made product. I saw these same brackets on other websites at quite a bit more than this price. You should definitely check this out!.
It has helped me build bookshelves and I am impressed with the quality, appearance, and ruggedness of the product. I have six shelves per 10 ft board, and I may have purchased too many. There are MORE THAN 30 books in each shelf, and none of them are bent or warped. In the case of the brackets for the wall, I had to get longer screws than those provided by the manufacturer because I was attaching them to a newly remodeled section of the house, in which a fresh sheet had covered up a section. Among the rocks. The purpose was to sink into the studs and make sure I had a good hold on them.
We are very pleased with the product in general. It feels like they are solid and substantial in your hand and there is no doubt that if properly installed into studs they will hold what you put Regardless of what I think of their work, there are two areas they might There are two sets of four that we ordered. On one of the boxes, there was the same marred area within the paint just below the bottom hole (indicating When everything is working, you don't notice it very much in the beginning, but when it's in focus it's also clear to see. I would say that this is a machining issue. The last part of this was that each bracket had a different angle (both angles). You will need to place the screws underneath/into the bottom of your shelf to correct this issue. In contrast, if I had intended for the shelf to just float on the brackets to make removal easier, it would have looked awful since the brackets were touching or not touching different parts of the bottom of the shelf (even with You may want to keep this We are renovating in a more rustic style, so these will work well for us. If I were to buy them again, I would.
These were a lot of fun to work with. My favorite feature is the way they look and provide solid support. I am not sure of the weight capacity, but they seem fairly strong and do not tilt forward. As I noticed, one of the brackets is just a little longer like an eighth of an inch or even less so that wasn't a big deal for me but I needed to know that before I installed them so keep that in mind before you install them.
11 were purchased by me. They look gorgeous on these brackets made of 25" mahogany. It wasn't a big deal at first, but when I tried on one bracket, I noticed it was a little low at the front edge, which was a concern for a shelf so items don't roll downhill and off the edge. There was a slight curve in the metal bracket I was working with, so I removed some washers at the bottom of the front margin to 'lift' the front edge. The point closest to the mount. The wood had to be positioned like this anyway, or you could put something under it at the front too, but then the bracket would not rest snugly against the wood. I took photos of the brackets that came with the set, and in the photos you can see the slight down-slant to the brackets Compared to a squared bracket, this bracket has a smaller angle. The solution I propose? The best part was that there were two who weren't There were two square brackets and two square brackets that were fine, so I kept the good (matching) brackets, and used the bad (matching) brackets on another shelf. I also added a few extra washers on this shelf since it had to match another shelf. As long as you don't catch this before installation, you'll end up with uneven shelving, especially if you rest the shelves on wood and don't screw them into the If they are screwed down, perhaps the issue will go away, however this uneven defect could cause problems to anyone who makes an effort to level the system. It gave me a.
My Home Depot bills for them came to almost $60. These were available for $35 and I thought I'd buy them and see how they are. The results were excellent! It was almost exactly the same as what you would find at Home Depot - for only half the price! Oh and they included the screws and anchors. This is not the case with Home Depot's! Now I'll order a few more of these and return the brackets from Home Depot! It is so easy to install these and they are extremely sturdy. All of the work was done by me. It's so secure in the wall and you only have to attach them to drywall, not to studs. The weight limits exceeded what I expected for these shelves and all of my family loves them. The wood, the brackets, the hardware, and the stain cost about $50 after the wood, hardware, and stain were purchased.
I reviewed many brackets before choosing these and am very happy with my choice. For the outdoor display of trucks and trailers I wanted, they were perfect for putting up on the deck for the shelves I wanted. They were easy to put up with my husband's help. He had a challenging time getting two, 2x6s into the space for each shelf, but he was able to flatten them with a little maneuvering and whittling. Having said that, they were stable and stayed in place without needing to be screwed to the brackets. I am satisfied with the quality of the brackets as well as the price I paid.
It's a nice look, and the idea is a cool one The problem is that they are difficult to install because both the quality control and the machining are inadequate. There was a set of four and a set of two. Three different lengths are present in each of those two sets of long sections. It may be a difference of a quarter to half It's only 1/8th of an inch between the longest and the smallest, but still noticeable when they're lined In the bottom section of the bracket which attaches to the wall, the machining is also poor. The holes are not centered and are, worse, misaligned The result of this is that they will almost certainly be crooked when installed. The fact that they were not made correctly is a shame, as they could have been pretty awesome.