Blue Sea Systems 7725 Safety HUB Fuse Block 100 RBS
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
With the plug attached, it has a wire that is about 8 inches in diameter and is 14 or 16 gauge.
Yes, you can branch as long as the total amperage is within the specification of the panel or circuit and the conductors utilized are the proper size.
In the picture below, there are four red wires being output from 4 small blade fuses (ATC). Smaller loads (up to 30A) are capable of being powered by these devices. The three high-quality files are sufficient if you only need them If you remove the red wires from the connector, you will be able to remove the current fuses.
is determined by the manner in which it is wired. There would need to be a relay that could take out the load of all fused circuits from
Selected User Reviews For Blue Sea Systems 7725 Safety HUB Fuse Block 100 RBS
Block of flexible high current distribution built on the basis of modular architecture. These Blue Sea DC components are very well made, as is the case with most of their components. During the manufacturing process, fuses are protected from water by gaskets inside two covers. The product does not work in wet conditions for me personally. The safety hub system I used is depicted in the upper right corner of this picture on the battery DC distribution and charging system for a mobile ham radio station. These cables are 00 gauge and 4 ga cables are directly connected to the MIDI fuses for high current. One star is being subtracted because the label provided by BlueSea contains space to write descriptions, but the numbers on the label do not match up to any printed or stamped at the fuse itself.
It's barely possible. The purchase I made has been satisfactory in general. I are paying a ridiculous amount for this, but it is worth knowing I am getting legitimate wires installed. In addition to the 4 small fuses, it also comes with the wiring harness and connector which do not appear in the picture. However, the fuses not shown do not appear to be included, which I more or less assumed would be the case. The only thing I wished they'd include was a few miscellaneous fuses with it since they're advertised on the site. The following points should be considered The local market has been hard to find MIDI or AMI fuses. There is a standard fuse that can be found at PepBoys and other auto parts stores, so I thought they were standard. It wasn't what I thought it would be. Although there might be similar fuse sizes that might work, I do not want to spend $10 on each fuse. In the end, I ordered the items I need from Amazon and now have to wait for them to arrive. It's also a good idea to have spare parts on hand, as you won't be able to drop by AutoZone to get one replaced. Although they're likely to be popular in marine applications, I use this little guy in my truck as an inverter, HAM radio, lights, etc. , so I made sure to grab a few more. As far as I know, it's not a big deal now, and they're not too expensive on Amazon It is as usual a rip-off to see the Monster Cable ones coming up first in a search. I had a pack of chugging gum and I got a pack of chewing gum.
This is the only fuse block that I found that was protected. Quality and value for the price were satisfactory to me. Essentially, I have a couple minor concerns that would not cause me to stop buying this *Brief description here There does not seem to be a way to replace the rubber connector. As a result of the ding during installation, I may not be able to connect the cover in time. In a tight environment, it is difficult to operate the cables that hold the cover on.
Considering there were no reviews on it when I purchased it, maybe this can help others. The power supply was installed near a battery for work lights and a power inverter in my work pickup. There are (2) spare fuse screws inside the cover, and all bolts and screws are stainless steel. Fuse compartments are impervious to water, so they can be mounted in most positions. It is also known as the Mini-MANL Fuse bottles are also able to fit in the (3) larger fuse slots on the ANL. A 5/16" lug can be fitted on any of the (4) positive studs. The overall dimensions are (8 inches). The dimensions are five inches wide by five inches high. Instead of a mix-up in the fuse box, I have a completely clean fuse block In the engine compartment, there are a matching set of fuse holders that are well protected and put in one convenient place.
I think this is a very good I really like it. The quality is excellent. The International Scout II's wiring can be modernized with the aid of this tool. It is possible that some people are annoyed by the leads on the ATC circuits. I actually find it to work well. To provide power to the stock fuse panel, I will utilize the MIDI fuses for alternator in and 30A for power output. I need to rewire the headlights with relays before I can use the last MIDI circuit.
Blue sea products are hands down the best quality, you will not be disappointed. Anyone who owns any Blue sea products already already knows this. It is the best bang for the buck and solves my problem for what I am using it for in an SUV. I assessed many alternatives before determining that this was my best choice.
Years ago, I used this method to fix a factory fuse box in a certain car. This is hands down one of the best options I have ever.