newlifeapp 1010A Garbage Disposal Mounting Gasket/Splash Guard Diameter 4" X Hight 3/4" Replacement For InSinErator, Kenmor
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Also, mine did not contain the cork part you are referring to. The piece you are looking at may not be the right one.
Selected User Reviews For newlifeapp 1010A Garbage Disposal Mounting Gasket/Splash Guard Diameter 4" X Hight 3/4" Replacement For InSinErator, Kenmor
As expected, I did the exact same thing. The rubber gasket/gasket that prevents things from falling down into the disposal was cut off as part of an older disposal we bought. My system is like new since I replaced it. As well as making the disposal sound better, it makes it more efficient. The following are some things to consider when removing the disposal and installing a First, insert a large Allen key (short end) into Two) the gasket fits over the mouth of the disposal and is locked It is not wise to stick the new gasket into the hole from the bottom. using channel locks to tighten the final few pieces of the disposal sink collar, pinch the eyelet and the You'll love it!.
It has a 3/4 horsepower motor — 605140. As a pro Splash back is not allowed. The cons are A great deal. There was no lack of research that led me to buy this
This was the OEM replacement piece that several websites recommended.
It was a pain to install this item. In order to remove my disposal from the sink and my sink from the counter, I had to completely uninstall the disposal. The flange also had to be trimmed so it would sit correctly, then I had to use an amazing amount of force to get the disposal pieces to come together again. Despite being sealed up tight enough to prevent water from leaking to the outside, the gasket does not permit the sink to drain freely. Despite the fact that I do not see any relation between these things. I am. The whole. A lot of people find it annoying. Why waited so long before returning the item? This time I won't have to go through that hassle again, since I have it installed already.
KENMORE 175. That's the one I have. Using a hydraulic car jack (truly not making this up) to push/hold into place so that the clamping ring would take hold. The new gasket was higher by 1/16 inch compared to the old one. It should be noted that the new gasket has to be seated/stretched onto the flange at the top of the The rubber part beneath the gasket doesn't feel smooth like the previous gasket. It looks more like a sand molded part. The drain hole is smaller, water backs up, food grease is deposited more in the sink when the water contains it. In the event that real Original Manufacturers Equipment is available somewhere else, I suggest purchasing it. In this case, a 1 minute job turned into a 45 minute ordeal in having to modify it so that it worked. It appears this issue appears in other reviews as well. It is a creditable company.
A 605560 combined with an ISE flange will solve the disposal leak issue. ISE replaced the 16-year-old Kenmore 1HP disposal flange and a brand new OEM gasket between the flange and gasket. Replacement was necessary due to leaks where the gasket splits causing the flange to rust. A water leak began to appear between the flange and the gasket as soon as the disposal was turned on. In order to avoid a complete ISE setup, I used this as a last-ditch effort. It was installed in less than five minutes and there was no leak, much to my surprise.
Grommets made out of textured rubber simply slip between the bottom of your sink and the top of your Considering the old one was toast, it was time to replace it. To install the new grommet, all I had to do was remove the metal retention clip, slot in the new grommet, and tighten I like it.
In my mind, I expected the CBC replacement to be a simple push-in. In order to replace my disposal, the old one had to be removed from below the sink, and the new one must be installed before I could install my disposal again. 45 minutes was the time it took me.
You got a lot of savings for the money you spent. I could not be happier with how it fit!.
The gasket of most disposals is this size. I've installed too many disposals to know any better. If you use vaseline on the outside, you may find that the disposal slides into place more easily.