Hoypeyfiy BB-UN26 Square Taper Bottom Bracket 68123/127 / 110mm (Black 1Pcs)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
It's alright
There is a possibility that it will fit if it has a 3pin crank
I would say that it will work if it has a "square taper." In this bottom bracket, you'll find lots of examples of an adapter for the square taper crank by looking up "Square Taper Crank" in Amazon. With the slight taper, the "squared" part holds the crank arm very closely to the bottom bracket because it "wedges itself" onto it after you tighten the screw on top. In order to avoid breaking something, you'll probably need to use a special crank puller to remove the crank arms/crankset from the bottom bracket. Maybe you should go to your local bike shop or visit a bike company if you feel uncomfortable doing this work If you need help, ask your op or a friend.
The bottom bracket shell is made of steel, so it will weigh slightly more than aluminum shell bottom brackets. Some people have stated that weighing theirs yields a more accurate weight for the assembly. This economy replacement part will add a couple of grams to your bike, but if weight is a concern then you probably don't want it. of going from steel to aluminum are not significant since I can get in better shape by going to the bathroom before I go out for a ride!
Selected User Reviews For Hoypeyfiy BB-UN26 Square Taper Bottom Bracket 68123/127 / 110mm (Black 1Pcs)
Due to other reviews stating it was a tough BB, I was unsure whether I wanted to buy it. Due to the lack of bike parts, I had to make do with what I had on hand. The bearings could not possibly be smoother, and I don't lie when I say that. As for longevity, I can't speak for it, but I haven't felt any flex or play after about 100 miles. It's a very good product. I'd buy it again.
I really like the pedaling system because it's easy to set up and install. I noticed there's a little bit of a wobble on the crank side of the crank set, or whatever it is that rides on the chain. This might have been my fault because my bike fell over and this might have damaged my crank, but it's best to leave it be. Can you update? About two months after I switched it on, I began to hear a clicking sound. It is not clear whether a warranty is offered when viewing this product page. I think the sealed bearing on my bike may have been damaged when my bike fell over. The pedal must have hit the ground, causing damage. Sadly, I have to replace the bottom bracket part because it did not fit properly and I did have to buy a different bottom bracket because I am not sure if it failed because my bike fell over or simply because it is not as tough as some other bottom bracket parts. The caveat emptor principle applies here. This means whatever you want it to mean.
Bottom brackets like this are cheap but do the job The spindle on one of my bikes was damaged and I needed a new bracket for it. In spite of the fact that the bearings are perfectly fine, the housing teeth are ridiculously soft and keep shearing off when being installed. For $14, this is fine for a beater bike to get back on the road. Don't expect quality at that price.
It seems to be a well-made, solid piece of equipment. These bottom brackets are not as high-quality as their copy of the Shimano UN sealed cartridge bottom brackets. In a bag, shipped loose. An angle was put on one of the cups when it was jammed onto the BB. In the end, I decided to knock it off with a steel punch and hammer by putting it in a vise and knocking it off with a steel punch and I still had to work on it for a few minutes before it finally came off. It wouldn't be good enough for me to call it The thread was threaded smoothly and correctly into the BB shell. The bearing is softer than the Shimano UN51 that was previously installed on the bike, but the old bearing had 30,000 miles on it, and it It would be nice to use a bit of antimicrobial The cups might seize when installed. Since they are steel, the seizing would probably occur with.
The bearing assembly I purchased fit perfectly on both my Genesis bike made by Kent and sold by Walmart. It was easy to install and performed as expected. An installation tool with a splined shaft will be necessary.
Surprised by the fact that my left crank was coming in contact with my Since it took me a long time to realize that the offset bracket was the reason why they sent me the defective bracket, i will have to absorb the cost. In my opinion, this should Even though this bracket is poorly made and may have been made incorrectly, it took me too long to figure out what was wrong and why it was hampering my work.
This product was damaged because the bearings were seated on it in an incorrect manner. Shell has scratches all over it. Considering the markings on it, it appears that it is a used bottom bracket, not a brand new one. This is also known as a BBS In contrast to un26 (which is made by Shimano), the un26 has different letters and numbers.
Despite weighing more than 260 pounds, I heard my old stock bearings snap and crack every time I put pressure There's a lot of smoothness and quietness in these new ones.