Saris CycleOps Fluid2 Indoor Bike Trainer, Fits Road and Mountain Bikes, Compatible with Zwift App
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
The resistance on the tire from the trainer is constant throughout the training period and cannot be adjusted without getting off the bike; however, unlike a spin bike, your actual bike has gears, and by shifting up and down the rear ring with your shifter, you will provide plenty of resistance and be able to change gears as often as you need to simulate climbing, speed work, and recovery. There are some excellent YouTube training videos that show you how to shift up and down on your bike while using a trainer. Best wishes to you.
A leveler is a device that raises or lowers the height of an object.
This isn't a "smart" trainer in the traditional sense. The original setup does not include any electronics. To track your progress, you can buy third-party devices that attach to your bike and communicate with your smartphone.
Yes, this is applicable to a wide range of bicycles, not just road bikes.
Selected User Reviews For Saris CycleOps Fluid2 Indoor Bike Trainer, Fits Road and Mountain Bikes, Compatible with Zwift App
This is fantastic. I haven't tried any of the others - It was, however, simple to put in place. It is common and easy to find in a variety of on-line stores. programs that run on the command line Zwift is a program that I've used. So far, TrainerRoad has been extremely helpful in supplementing my training when I am unable to ride outside. br>br>Questions I had when I first started out (for beginners):
- Is there anything else I need to ride? You'll need a front-wheel block. On Amazon, a basic one costs around $6. And, most likely, a floor mat; mine cost $26 on Amazon.
- Is there anything else I "need" that I don't actually need? Speed and cadence sensors (mine were $55 on Amazon) are highly recommended. You'll need it to integrate with other programs - I got ones that connect to my watch, such as Zwift and others. You'll also need a USB extension cord and an ANT dongle ($20-$30) if you're doing them on your computer. (Amazon charges $25 for both. ) Also - It's so nice to have a fan. I have a small "desk fan" that works great for me.
- What are the best programs for me to use? I recommend that you try all of them. TrainerRoad is only $12 per month and Zwift offers a one-week free trial. Rouvy offers a two-week free trial. It was simple to stop at the end of the month. Give each one a shot.
- That was a snap- This requires me to use a release bar on the back tire. First and foremost, is it included? Second, is it okay if I use it outside? Yes, yes, yes, yes, yes, yes, yes, yes, yes, yes, yes Simply leave it in once you've changed it. I didn't realize it and switched back and forth for the first three or four times, and while it isn't a huge pain, It's an extra step that isn't really required. You can simply stay in CycleOps. br>br>Have fun with it. br>br> Get to work on your training!.
I wanted a machine that was well-made and would provide a comfortable ride. I liked the way it felt when I pedaled, so I was willing to pay a little more for it. All of that is accomplished by this device, and I am extremely pleased with it. To mount my Specialized Pitch mountain bike to the Fluid2, I needed to use the CycleOps skewer. At around $13, it's not a big deal, and it's a quick swap. The bike was quickly and securely installed. I started spinning on my bike with the knobby wheels and it worked fine, but there was a lot of whirring noise, which was fine for outside, but I decided to switch to smooth tires and the noise is nearly gone. The only criticism I have is that the maximum tension isn't particularly challenging. I'm a new spinner, and so far the tension has been fine when I'm pedaling in about 15th gear; however, as I gain strength, pedaling in 18th gear (my bike's maximum gear) becomes too easy- So, how do you proceed? In addition, here's something else to think about: According to what I've read, this trainer has shredded the street tires of some people. I've noticed that after spinning for a few minutes, my rear tire gets a little warm to the touch, and there's a little residual rubber on the flywheel's smooth surface. I haven't noticed any "shredding" yet, but it's too early to tell because I've only used it for a few hours.
The action bolt (I believe that's the name for the piece that slides in and is tightened by the key to connect to the skewer and hold up the bike) does not fit or slide into its place. I tried everything I could think of to force it into the plastic opening, but it won't fit without a hammer. Perhaps the plastic was molded too small, but based on product photos from various sellers, I believe I have a mix of pieces from current and older Fluid 2 models. I was so disappointed that I didn't even get to try the product. I read a lot of reviews before and after purchasing, and defective pieces are mentioned fairly frequently on various seller sites. br>br>The instructions are actually clear, so when it says "slide it into place and turn the key to lock," I knew something wasn't right with the fit on mine. br>br>I read a lot of reviews before and after purchasing, and defective pieces are mentioned fairly frequently on various seller sites. Which is a bummer because you get a card signed by someone for quality control in the box.
It's a fantastic trainer that's also very simple to set up. It took about ten minutes from the time it was taken out of the box to the time it was ready to be used. It has a smooth, road-like feel to it. At 76db and 80rpm, it's also very quiet. I've had this trainer for about a week and have only put a few miles on it because I still ride outside. However, as the weather turns colder, I'm looking forward to doing more indoor riding. The trainer also allows you to make adjustments to your bike's fit and record your riding position.
It's fantastic - with a smooth-tired road bike - It takes a lot of time to set up - It's quite peaceful - I subscribed to Zwift and bought a wahoo speed and cadence sensor as well as a heart monitor. I now have some fantastic indoor cycling equipment. much less expensive and superior to alternatives.
I have to believe that because it was delivered without all of the purchase materials, and I am unable to use it at this time. Bummer. I'm not sure if anyone else has experienced the problem of missing two bolts and a knob. I was let down. br>br>Recent changes: br>br> I explained my situation to Cycle Ops, and they are sending the missing parts to me. There was no fuss, just good customer service, which is an improvement!.
Purchased for those cool, windy days when riding on the roads is too taxing on the body. I'm 75 years old, and my cyclocross/gravel small knob tread is 40mm x 700mm. When I exercise at 75 pedal strokes per minute in the second high gear (52 tooth chainring and 13 tooth cassette), which is about 26 mph on the road, these tires whine quite a bit. I couldn't imagine using this trainer on a mountain bike with a lower gear ratio because the fluid resistance would be too low. I wish there was a way to increase resistance because I could pedal at my training heart rate for hours on end. My 700mm tires were difficult to mount, so I'm not sure if this would work for 29" tires. They might, however, work. The skewer is included in this unit, despite the fact that the web ad makes no mention of it. I'm considering remounting my other road tires with a smoother tread, but it'll be a pain and spring is just around the corner! Yay! Structure that is strong. It appears to be of long lasting quality. The packaging is very nice.
Related Products For Saris CycleOps Fluid2 Indoor Bike Trainer, Fits Road and Mountain Bikes, Compatible with Zwift App
