Sea-Dog 327199-1 Removable Rail Mount Clamps for Round Tubing
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
There is no way for them to fit 7/8" rails directly. 3/4, 1, 1, as stated in the description. It can only be 25” in diameter. To accommodate 7/8" rails, you need to modify rubber or fabricate rubber. Here's how I know I have 7/8" rails I have 7/8" rails.
In spite of the fact that it can support the weight, it is not designed not to rotate and most barbecues are mounted outboard of the side of the A further drawback is that it is made of plastic and might be exposed to damaging heat in the application you have described. In that case, I would consider paying for a barbecue mount that is specially designed for your There are mounts for almost every mounting scenario, which is why manufacturers have designed them. If Sea Dog clamps are used to mount a barbecue, finding out the hard way they don't work can lead to a catastrophic loss. Being safe is better than being
The pair in a pack is the same as one pack
These rubber shims are affixed to the flanges. These bolts will not turn or slip if they are tightened. These are the tables I use on my boat for the cockpit. I use an extra piece of rigger's tape in place of shims since the pipe diameter is so large. I've found it to work well
Selected User Reviews For Sea-Dog 327199-1 Removable Rail Mount Clamps for Round Tubing
They are excellent clamps, in my opinion. One key aspect that may not be obvious to some users is one you should be aware of. As part of the clamps, you get the following Two strange-looking grey washers with little loops around the inside radius were found along with screws, lock washers, butterfly clamping screws, and two weird-looking lock washers. Take them out of the trash instead! These washers are for the butterfly clamping screws, and should be installed on the inside of the clamp so that the butterfly screw does not fall out when the clamp is being loosened. The only thing I can tell you as a sailor is that, no matter where you drop stuff on deck, it will inevitably, without a doubt, blow out overboard, so these little retaining washers are important. Another small surprise is that you'll have to push out the nylock nuts in the mounting plate in order to attach the mount. They are securely attached, but they'll come out as the mount is attached The mounting screws will start to loosen when you try tightly to tighten them, which will make it seem like you have a stripped nut or something is awry. It was the Nylock victory Once it has been pushed out, it will not engage with the screw. Make sure you keep that in mind when you assemble them. According to me, if the nylocks had been secured from rotation as well as from push out, it would have been much better. The rest of the arrays (mine are 100 W) can be mounted with these, and I believe this is an excellent solution. However, I may be a bit concerned if you go to substantially larger or heavier arrays.
The solar panel is 50W and the rail is 7/8" wide. Everything has gone well so far - Currently, our 7/8" stainless steel boat rail is holding a 50W solar panel. The cable works just fine and keeps it in place.
These came in handy on my sailboat when I added cam cleats to the dinghy davits. Here's the photo (if you don't understand what those words mean) . A pre-approved credit card was available to me My only difficulty was that I could not only drill holes with the captured nut, but I could also The blocks are of high quality. I plan on buying other accessories for this item as well.
Make sure they don't rust. Sometimes, the angle makes it difficult to screw them together. You can use it in a lot of ways.
This sea-life is present in these seas Stainless steel fittings appear to be used on the dog clamps, where a material similar to Starboard is used. Rubber inserts make it easy for you to fit the clamp on different rail sizes with little effort. The fittings didn't match what I wanted but I was able to create slots to insert stainless steel hose clamps through one end, which enabled me to fasten the tubes I wanted.
Fits different rail diameters and has materials that are suitable to operate in ocean conditions. In addition to the rail-related applications, I plan to purchase additional ones The mounting has been raised.
The prices on Amazon fluctuate a lot for these, but they work great. It is a must to choose Prime, I have bought items from other sellers twice, and have waited more than a month for them to arrive.
A very strong plastic, nylon, is used for the construction of these shirts. There are no copper components all the metal parts are stainless steel (probably 304) so they should all be relatively corrosion-resistant.