ZIPLEVEL PRO-2000B High Precision Altimeter with 75-Feet Cord and User Guide

I purchased the Ziplevel for one-person use and for use in multi-level foundation construction where a laser level was not feasible. One-man laser levels, on the other hand, are now widely available, but they can still be difficult to use in some situations. br>br>Right from the start, there were issues with the Ziplevel; I had to figure out that the wind blowing through the cord would cause measurements to be off. Any cord that is not laid flat on the ground will blow around in a strong wind, preventing a reading from locking. It was fine once I realized that the cord needed to be held taut and motionless for accuracy. I did, however, check with a laser level on a regular basis to make sure. However, I became wary of readings after that, and this suspicion grew as readings became increasingly inconsistent. For the majority of my foundation work, I reverted to using a laser level. br>br>Then, after a period of inactivity, I took it out and discovered that the unit's accuracy was poor. It continued to give readings, but they were alternated with "Cord" on the display before giving a second, different reading. Since Technidea claims that the unit does not require factory calibration, I remembered that the cord had to be completely still, with no wind blowing through it. Despite being held motionless and in the absence of wind, measurements taken inside a house still flashed "Cord. " It was then that I discovered on the Technidea website that, while the unit does not require factory recalibration, the cord does require factory gas recharging, which costs $200 (plus shipping). And the recharge, which costs $200 every three years, is required. That information is not readily available on the website or in the user guide, and you must delve deeper into the site to find it. br>br>The user guide simply states that if "Cord" flashes, the unit must be returned to the factory for repair. It does not state that the unit needs to be repaired by the factory every three years at a cost of $200 per repair. If I had known, I would have looked into other options instead of buying the Ziplevel. I needed the Ziplevel to make a contour map over a large area, so I bit the bullet and sent it in for repair. Buyer beware, br>br>.

Royal Barr

| Dec 14, 2021

I paid an additional $35 for shipping and received standard delivery. It's quite effective. Even if you pay an extra $35, Technidea is not in a hurry to ship. I'm not convinced it's any better than the smart leveler, which is significantly less expensive. It does, however, need to be recharged. This is not the case with Smart Leveler. br>The zip level stick is essentially a monopod that can be purchased for ten dollars at Walmart. br>The metal pieces that hold it down could be made and replaced with any long stick.

Gemma SLATER

| Aug 04, 2021

For outside work or non-line of sight leveling, there is no comparison to lasers. Hands down, it outperforms lasers. How long have you been searching for the dot outside? Or how about putting in floor sills around a corner? Because the laser dot grows larger with distance, accuracy suffers quickly, making it unsuitable for laying out anything beyond 50 feet. I designed a 3,600-square-foot "U"-shaped foundation with a obstructed line of sight. This was the only option other than hiring a survey crew, which is why I bought it. However, for laying out sill plates and concrete footings, it quickly became my go-to tool. It is precise and can be operated by a single person at high noon. If you have a laser, give it a shot. Yes, I still use lasers inside where they can be seen, but the Zip is my go-to for everything else. BTW, the $180 recal fee is a steal with daily use, as I've had it for 4 years without service.

Drew Jarvis

| Jul 28, 2021

We've been using the Zip Level Pro for a while now. At my place of business, we've been using the year 2000 for a few years now. It was a good substitute for self-leveling laser elevation equipment that requires a line of sight. Of course, because the ZipLevel is connected to the base unit by a cord, it has some disadvantages. In an ideal world, one would have both types of equipment and be able to choose which one to use depending on the conditions on the job site. br>br>Overall, the ZipLevel is a high-quality product; I did damage one cord (due to a thorn puncture), but the manufacturer quickly replaced it. And I've broken four (four) of the "unipod" sticks that hold the receiver. The unipod is made up of four sections that fold in on themselves like tripod legs. When you loosen a collar, the next section slips out, and you tighten it to keep the section in its extended position. The issue is that the collars use too fine a thread and are prone to stripping, which is exacerbated by the fact that the material is soft aluminum (which is good for weight but bad for fine threads). Worst of all, the unipods are pricey, around $75 if my memory serves me correctly. I've started saving broken unipods as a habit. Usually, only one collar will strip, allowing me to disassemble it and save the remaining three sections of the unipod for future repairs. I've already avoided having to buy two unipods as a result of this. br>br>In addition, I believe I should mention that the manufacturer is extremely easy to work with. Parts, service, and repair are all available. It's always been simple to order directly from the manufacturer. They ship quickly, and because they are based in Escondido, California, the packages arrive quickly as well.

Bjorn PICKERING

| Jun 01, 2021

This is something I should've purchased 20 years ago. I was hesitant and didn't spend the extra $100 or so for the pole and accessories. I now regret not doing so, but I believe I could get the accessories for less at Home Depot or Lowe's.

Nolan Saunders

| Feb 17, 2021

When I got this, I got rid of my laser units. I use it to build retaining walls and grade small areas, and it's a fantastic tool. Before you buy, do some research to make sure it'll work for your needs.

Devin Coffey

| Aug 06, 2021

I'm in awe of what you've done. It's been used to level houses, construct decks, and install beams. It makes my job a lot easier.

Kobe Riggs

| Aug 07, 2021

A measurement cannot be repeated. It had been three weeks since I received it. The temperature sensor had failed and was sent back for repair. It was just returned to me, and it has the same issue. I'm sure some of these units are functional, but they haven't been able to find one that works for me.

Briar Travis

| Jan 06, 2021