Lynk Professional Double Drawer Pull Out Two Tier Sliding Under Cabinet Organizer, 11w x 18d x 16h -inch, Chrome
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
There are two separate parts to the track and shelf. order to install the track, the base of the cabinet is screwed to the track. A nut is attached to each corner of the shelf, thus linking the shelf to the track. I believe it would be pretty easy to remove the shelf from the track if you needed access to the plumbing. You can attach the upper shelf to the lower shelf using stainless steel rods that fit into female slots on both of the upper and lower shelves if you are considering the two-shelf unit. If you needed to remove the upper shelf, you could do so easily. The corner of my bathroom sink is now divided by a two shelf unit. Even though it was a tight fit, it works just fine. It is a good product. If you needed to remove it in order to get to some plumbing, you could do it in a ten-minute job.
That is correct. The dimensions are 14" wide, 18" tall,
At least 29 would be a good estimate. A 5 inch diameter.
In short, yes. It's better to use the oval crockpot. I think it should fit, but it depends on the size of the instapot.
Selected User Reviews For Lynk Professional Double Drawer Pull Out Two Tier Sliding Under Cabinet Organizer, 11w x 18d x 16h -inch, Chrome
I think there are better options out there that open fully AND feature independent drawers on either side for maximum convenience (e. g. ). The Revised Version In the shelf). Ratings on Amazon have less and less credibility for me.
The drawer opens straight out into the front I can barely see my tiny lip through it! There are always some in every cabinet! A board was placed under it so it could be lifted about half an When I pulled the drawers out after all that aggravation, half of them were extended. You have to still get on your knees and dig the stuff out of the back of the drawer. Since both sides are connected, you cannot even reach the things on the bottom rack because of their close proximity. There is no design any dumber, more ridiculous, or any more stupid than this. Even after the hassle and frustration of trying to put it in the cabinet, I took it out before I could get it in there and I will be returning it, since this is the most idiotic rack you can I actually had a hard time reaching stuff in the cabinet because of it.
It is well built and does the job it should. One of the plastic corner tubes was missing when I assembled mine, which caused me to be a little disappointed because I thought I would have to return it. As I expected little from Lynk, I sent an email about the issue. A pleasant surprise was receiving an immediate response saying that they would ship out the entire shelf as they did not have the tube in stock. Having the shelf within two days was no big deal to me. Their customer service is outstanding and I would give them five stars for that alone. These days, it's rare to see something like that.
I wanted one for a long time, but find that the prices appear to be too high for the little extra space that it will provide. There were a lot cheaper ones, but this one was almost half the price. First, let's get the assembly going. This is easy! To connect the two baskets, there was a wire and then a few screws to connect the bottom to the track, and then a few more screws to connect the track to the The unit comes with a guide that will help you not mount the unit too close to the edge of the I think the weight of the unit makes it less strong than I would have liked and this results in it not coming out as much as I would like. This product gave me about 40% more space inside a cabinet than the one I would have bought custom shelves for. The biggest benefit is the fact that it moves out, so I don't have to reach all the way to the back, and it rolls out over the top. The design is attractive and adds a nice touch of ergonomics to any Anybody who has cabinets with poor shelf designs or to those who cannot reach the back of their fixtures will find this highly useful.
In order to keep the mess beneath our kitchen island at bay, I bought a couple of Lynk cabinet organizers. I was impressed by the quality of the organizers, as most other reviewers were as well. In addition, I was pleased to see that Lynk made modifications to their design in response to an earlier review that disclosed a simple There is no longer a need for nuts to attach the shelves to the glides since the screws attach the shelves directly to the glides. Some reviewers commented on how challenging it was to attach nuts inside Several years after those reviews were written, Lynk had changed the design to use a threaded hole that is cut into the glide. Screwing in four Phillips head screws with a screwdriver is all you have to do to attach the shelf. I was not able to do it in more than five A big thanks to Lynk for being willing to make During installation, the process is very straight forward. It has been complained that the lynk organizers do not mount on the sides of the cabinet interior like the Rev-A-Shelf organizers do. Stacks of shelves. This is unfair in my opinion The two organizers are used in different ways. It was important for me to use organizers that would mount to the underside of the cabinets because I had a kitchen island with two bays 31" wide with double "pop out" doors. It would not work with any other type. When I installed it, I ran into a minor hiccup Along the base of my cabinets, there is a 1/4 inch lip. Consequently, the organizer is rendered ineffective because it makes it impossible for the glides to pull out. Here are a few suggestions I came up with to try to resolve the problem Using the fender washers to raise the glides, 1) removing the trim piece and cutting it down 1/4 of an inch, 2) installing a 1/4 inch riser of hardwood from the hardware store, and 3) removing the trim piece before installing the hardwood riser. As you can see, I went with option 3 The washers located on the fender. In my local hardware store I got four 1" fender washers as well as a box of 1" fender washers. This pan measures 25" in diameter I am my own head Wood screws need to be drilled. I needed 16 washers total, since 4 washers stack to exactly 1/4 inch. In advance, I would like Using a 1/16th inch pilot hole, drill 1/16 inch holes in the bottom of the cabinet and then install the glide frame. It took no more than fifteen minutes to complete the whole process, aside from the run to the hardware store. You will need multiples of 1" fender washers that are stacked to the correct height for each Lynk organizer you want to raise over your lip. As an alternative to using washers if your cabinet bottom has a lip that is higher than 1/4", I would suggest purchasing hardwood strips and gluing / screwing them into place. I found the washers to be perfect for my application. This is at I paid approximately $4 per piece, which amounts to 18 USD each. Hardware, including screws, cost a total of $800. The organizer is extremely useful, so I am very pleased with it. By doing so, we can use our kitchen island to its fullest extent and make access for items tucked away in the dark recesses of the island easy. I'm very pleased with the quality of this product. There is a lot of weight on the glides. A bunch of large Calphalon pans should stand on its own. I prefer the Lynk organizers for their price, although Rev-A-Shift ones still hold their own Stacks of shelves. The Revised Version Shelf options are also nice, but unless you want the functionality of independent pull drawers AND the ability to install by attaching to the sides of your cabinet, the Lynk organizers are more than adequate. In the future, I plan to purchase more of them and install them in other cabinets.