Neoteck DTI Digital Dial Indicator 1''/25.4mm | Digital Probe Indicator Dial Test Gauge High Resolution: 0.0005''/0.01mm

So on the whole, this is a pretty decent piece of kit. It is actually less important to measure the accuracy of an instrument than how consistent its measurements are when it comes to spine-matching arrows. It is difficult for me to draw conclusions from the data I have, but I report that when I measure the same three arrows ten times each, I obtain the same values for deflection and spline.

Trey Atkinson

| Nov 30, 2020

In recent days, my son has given me a 3d printer as a gift. For "no cost" method of leveling the bed, which is needed to get good prints, you can insert a lot of paper under the nozzle of the print head. Adjust the bed one corner at a time by bending a sheet of paper to fit between the nozzle and the bed until there is a "small amount" of friction when you pull the paper out. It is important to repeat the process until all the corners feel Generally inexpensive printers can print at 0. Because there are so many reasonably inexpensive printers available. This method is OK but not great for accuracy of 1 MM. My printer has a 3D printed bracket that I can use to mount this Neotek dial indicator on the print head. The first test I conducted was using the sheet of paper method to level the bed and the dial indicator by Neoteck to confirm accuracy. As a result, a sheet of paper method could be off in some cases by a factor of A printer's accuracy is a little more than 5 MM, so this is about 50% of the printer's accuracy. In order to use the Neoteck, you need to insert it into the clamp, and then push it onto the print head using friction. Once you have a G-, you can use it You can use the code files to position the head exactly to each corner and adjust it accordingly. It is also possible to move the head manually to achieve the same effect. To get the bed almost perfectly level, it usually takes two passes to adjust and reverify each corner. Additionally, I've found that the bed leveling can change from one print job to the next, even if the jobs were printed back to back without turning the printer off. There are also opportunities for a bed's leveling to change by a few degrees depending on how warm the bed is and if the air in the room circulates. It is necessary to heat the bed to ensure the very first layer sticks. The bed is not level when just a little bit is off, and I have seen what happens when just a little is off. It is possible that the first layer will not stick to some points or you get some "strings" on the first few layers if the design requires that the print head move This Neoteck device is very durable, and it has a very nice case that fits the device perfectly. You almost never need the instruction manual because this tool is so easy to use. There is a high degree of accuracy in the data. The whole thing costs Therefore, this really cheap solution has improved print quality and has reduced the number of times you need to "do over" a layer pass when the first few passes do not You may be able to solve your printing problems if it has to do with bed leveling if you are using a digital gauge without a digital gauge. For those of you who are interested in trying it, I suggest searching your favorite 3D pattern website for "Bed Leveling Bracket" and "Neoteck. ".

Ellianna Harrison

| Nov 08, 2020

It works wonderfully for my purposes after printing a mount for the x axis. The bed can be leveled very accurately with this method. Recommendation of the highest standard.

Ayden McCarty

| Feb 13, 2021

This is what I use to level my 3D printer bed. It's impossible to print a carriage adapter from Thingiverse that fits the loop on the back of this indicator. I found it useful that to set the gap and to level the surfaces, the two processes were able to be separated. Set this indicator as soon as possible to set the distance evenly over the entire bed between the X axis and the bed surface. After that, set the bed gap near the center of the nozzle so that it is By getting consistent filament "squish", you are able to achieve excellent adhesion and less/no curling of your parts.

Mabel Caldwell

| Jul 07, 2021

This was great to have, but I had to build myself a mount for the indicator that fit into the miter slots, which took a few tries to get it to work, but once it did, it The alignment metric I used helped me align my table saw to within 1/1000 of an inch, and it cut like butter once I had it set up. The mounting plate has the ability to be rotated so that the eyelet faces horizontally or vertically, giving you plenty of flexibility when setting it up.

Ariella Simmons

| Apr 26, 2021

With the exception of the RS232 port, I found it to work fine. Nice device, good workmanship, I'm sure it's a good device but the description should be revised to remove the information that indicates it can be downloaded. It is a problem that there is no plug that is suitable for pairing up with typical data connections. Interested parties can purchase a separate transfer cable from clockwise tools, which has a micro-USB connector. There is no feature like this on the Neoteck. I recommend you look into purchasing the Clockwise version of this indicator, which is shown with a USB port if you don't want to down load to excel or other electronic data transfer systems. Otherwise, consider purchasing the clockwise version shown with the.

Noa SWIFT

| May 29, 2021

The video output protocol is a Chinese serial protocol.

The resolution on screen is 0 mm. A measurement of mm on the data port is a resolution of The screen resolution is twice the resolution of 005 (TWICE the When the idle spindle is in motion for a prolonged period, the automatic turn off is triggered. Given the low cost and higher resolution than advertised, this is a 5 out of 5.

Livia Wagner

| Jan 05, 2021

For the price, it is a great buy, but it is similar to what is available Using the magnetic arm mount is simple since the mounting plate comes with a backing plate. to find that the indicator would no longer fit in the case after you put the backing plate on. Despite its apparent beauty, no one wants to constantly have to change the backing plate whenever they want to store the case.

Elliot Reed

| Oct 09, 2020