Amico CUT-60HF, 60 Amp Non-touch Pilot Arc Plasma Cutter, Pro. 95~260V Wide Voltage, 4/5 in. Clean Cut Cutting Machine

Here's the introduction Because of my short experience with the machine, I am not assured this review will be accurate. In the beginning, I was leery about buying this machine for my needs, but reviews on the other products, as well as experiences with other manufacturers, convinced me otherwise. There was a need for a plasma cutter that could cut 1" material from time to time. Initially I contacted the "green" company, but did not receive a reply, then I contacted the "black PW" company, but received no reply, and finally I contacted the "yellow WP" company, and they suggested 3/4" was the maximum thickness.
I think I will be able to cut 1 1/4”, but I do not have any on hand to test cut. I don't like 1", but must occasionally cut it. So this machine was either going to cut 1", It can cut up to 1" in diameter, as shown in the pictures. I am satisfied with that result. Is there a reason four stars are awarded? The pilot arc is not perfect, granted I'm not using the cleanest material, but I wanted one due to the fact that I'm not using the cleanest material. On thinner materials, it sometimes lights right up, but dies in the cut, then lights up, and so on. I'm not sure if it's me as much as if it's the material I'm cutting, or even the ground. The router keeps starting up if I keep trying to cut, but it is a bit annoying to have it keep doing it. There's another thing I don't like, nitpicking again, the ground lead is a small DINSE connector. It's not a big deal, but I was hoping to be able to use ground from my TIG to minimize clutter on my This isn't a huge problem, but it is something to consider. So far, I'm quite pleased with how well it cuts through 1/4" plate like it's not there. It makes a really nice cut, too. It is ridiculous to try to print 1/16" sheets with this machine! For consumables, I'm sure you wonder as well, these are direct replacements. I have not verified their quality yet, but they fit as follows It's going to be tough to beat in terms of bang for the buck. A quick update Saturday, Jan 18th, my machine blew up in dramatic fashion! I sent an email to the company that day, hoping for a response by In just six hours I received an email with a printable shipping label! I was ready to ship by the following Monday. After I sent it off on the 22nd, I forgot to get it back to you. In either case, they told me they would rebuild the machine or send me a new one and not to send the cables along with it. Several days ago, on February 7, I received an email informing me that a new machine was on its way, and today it arrived. That qualified them as five stars in my book that is a pretty good level of customer service.

Kyrie Ayers

| Dec 09, 2020

I repair construction equipment thus this Plasma Cutter is a great purchase at a great price. As a steelworker, I use this machine for hundreds of feet of steel and it has never let me down.

Regina Curtis

| Sep 12, 2020

With a much better torch, the defective one was replaced as quickly as shipping would allow. There is better customer service at this company than at Costco, in my opinion. In my experience, the plasma cutter works better than a more expensive one, but I cannot imagine how a more expensive one would operate better. The weapon cuts through thick steel like butter with a simple pull of the trigger. Couldn't think of a better way to go about this. It is highly recommended that you use.

Walter Trujillo

| Oct 29, 2020

These are great value and always cut perfect. Each of them is a great machine. Although I still use the Cut 50, I got a plasma table and needed these high definition starters since my plasma table had a hard start. My recommendation is for anyone to buy this machine because it is fast, clean, and works well.

Kimora Sparks

| Jun 11, 2021

The machine is very good for the price. It cut 3/4" thick steel at a reasonable pace with a single pass. It has proven to be more useful than I ever expected I'd normally have used cut off disks where I'd have normally used cut offs. The clamps, torch, and connections are not flimsy at all, they are tough enough for constant hobby shop use.

Dakota Townsend

| Feb 26, 2021

This amigo cut machine cuts through metal like butter and I don't have to use my gas welder torch to do it anymore. Thanks for making such a good machine.

Ella Shea

| Apr 17, 2021

It appears to be working properly straight out of the box. I can't wait to use it more and see how Having returned a yellow one that didn't do anything, I am thinking that this one deserves to be kept.

Bowen Melton

| Feb 21, 2021

I expect that it will work. The 1/8" steal slips through like butter with the hot knife. I have cut up to 3/8" AR plate with an acetylene torch it works better than a router.

Emory NORTH

| Feb 06, 2021