HFS(R) 4" x 4" 100mm Stainless Steel Lab Jack Scissor Stand Platform 3kg/6.6lbs Load Bearing 3kg/6.6lbs
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
It is understandable that you would be frustrated with the jssp-based In the comparison table, the 12-inch by 12-inch by 15-inch jack is displayed however, when you click on the image or label, it isn't displayed. I am sure that you can easily locate this jack somewhere else if you must have it. I was able to find one in just a few moments. It is also possible to use StonyLab 11 instead. The size of the paper is 8 x 11 inches. Lab Scissors Jack, 300 x 300 mm, Stainless Steel Laboratory Support Jack Platform Lab Lift Stand Table, Expandable Lift Height Range from 100 mm to 450 mm, Support Weight 25KG is also available on Amazon, but it is three times as much.
No junk here, it's of "LABORATORY" quality. There is actually an effective weight capacity of 60 pounds, as the manufacturer claims
It takes about one hour to walk around the ball park. A width of 8 inches or a height of one inch Another brand says 7/8. Since most of these are knockoffs of each other, I would guess they are close in size.
I don't think much has happened. As a result, it has a light build, and though no weight limit is specified on the packaging, I wouldn't use it if I weighed more than ten pounds. It's best to keep the weight at no more than 5 pounds in most cases. with a weight of 5 pounds, it will be very difficult to lift the weight. The rate might not be lowered Since I usually adjust it to around the height I need or a little above before putting anything on top, I usually have enough height before I put anything on As of now, I have not gained more than a couple of pounds.
Selected User Reviews For HFS(R) 4" x 4" 100mm Stainless Steel Lab Jack Scissor Stand Platform 3kg/6.6lbs Load Bearing 3kg/6.6lbs
If you like This scissor jack is horrible! This means that unless it's at min height or max height, it is not a solid object. The ball wobbles all over the place. I would compare it to a kid's toy rather than a scissor jack for a laboratory. There is no need for you to buy this as it is useless. To top it off, Amazon wants me to drive to a UPS drop off location to return it. I can't get a label from them. I was disappointed.
I used this for my router table so that I could adjust the height of the router easier and keep the router from sliding around when I was I really like this! Height is easily adjustable, and it stays in place when you increase or decrease it.
With my drill press, I needed a jack stand that could stabilize the long material and allow me to drill precise holes. This sounded like it would be a good fit just based on the description and pictures. In the end, however, the item turned out to be a bit disappointing. It has both sharp and jagged edges on the top and bottom plates. There are small screws threaded into the rubber feet Holding on by the hair of their necks. There were scratches and markups on the protective film covering the top of the plate that were beyond what was possible with There is a possibility that this is a knock-off There is a chance that this is an Eisco Labs stand (which is about twice as expensive). I returned this one and got the original Eisco Labs model CH0642B instead (it is not stainless, but rather powder coated steel, but has a nice quality feel and fits my needs perfectly).
Exactly what I needed for my new In the bottom, I put the new table that I took out of the old one. Objects up to 2 inches thick can be accommodated. Rather than focusing on the surface of the table, my K40 focused below it. With the table height now adjustable, it can cut the 1/8 acrylic at 18mA in one pass.
The fit and finish on this item are bad, and it appears to be worn out. Within 30 seconds of removing it from the box and handling it for the first time, I cut myself. There are screws on the top plate that do not line up with the top plate, so if you cover them with something large and large enough to go over them, it will not The item was going to be used with a diode laser engraver, but we will be returning it instead.
For my Chinese K40 Blue/White laser cutter/engraver, I bought this as a manual bed lifter. If you close it completely, it fits, but you don't have much room for raising the bed. If this application were mine, I'd opt for the smaller size. A 3-star rating for me I gave it two stars because it does not seem to fit my application, but it works.
The size of the artwork is 8 by 9 inches. My order was supposed to arrive within two weeks, but when it did not, I contacted the seller who said it would be fifteen days until they received and shipped it. I ended up canceling that order and finding this lift instead. I believe we will be able to alter it to work with our application, but it is a little too big for it right now. It was challenging to remove the protective cover over the stainless steel top plate, and there was a small amount of residue left over after cleaning. This will be used on an ESD protective mat since we will be touching it. It will be necessary to remove the rubber feet and replace them with 10-inch steel feet Spacers 1/2" hex x 1/2" long and screws 1/2" long with star lock washers made of stainless steel.
Upon unboxing, you can clearly see the product is used and Unfortunately, this is very disappointing, but we can deal with it. While it enables me to elevate my computer monitor that I bought it for, by turning the screw adjustment I usually raise the left side of the platform, and then have to pull up the right side of it to make it work.