Vestil FJB-36 Basement Floor Jack, 19" - 36" Height Range, Maximum Height Capacity (lbs.) 6863, Minimum Height Capacity (lbs.) 9738
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
It looks like they will support that perfectly. They are not "permanent," however, as you can't use them as supports during construction. You just need to keep the relative humidity around 40% where they are installed, and they last a very, very long time.
Bottom and top plates have the same size and thickness. The top plate measures 6"x3 1/2" and the bottom is In the screw post case, one plate is welded to a large post and the other to a small
A base plate for the Jack measures approximately 3 inches in width and extends about 3 inches out from the jack itself. There would be little room for error. In addition to the precast cap block, most builders use a wide top and bottom square block that measures 4x8x4. There are some areas that have concrete patio blocks that are 4x8x2 1/2, which are
A 36-inch screen will fit it. Moreover, if you'd like one that is taller, I have that as well. Another one of my previous ones must have been over 6 ft
Selected User Reviews For Vestil FJB-36 Basement Floor Jack, 19" - 36" Height Range, Maximum Height Capacity (lbs.) 6863, Minimum Height Capacity (lbs.) 9738
My house was built in the 30s with a stone basement, but over the years they added a 17' long by 7' wide back porch laid on a slab foundation crawlspace. There was a time when the porch was enclosed, and a garage was attached Anyway, I just want to say that this room works perfectly for my home office, but there is a lot of bounce in the floor due to the long joists. To anchor everything down, I built three triple 2x6 headers and put them perpendicular under the joists. I used the jacks to tighten the whole thing It is no longer possible to bounce on The manufacturers state these jacks are temporary, but in this case they remain for life. If freezing or thawing cause problems, they can be readjusted to ensure they work as they should. In terms of performance, they worked great and were very heavy-duty!.
It is a great way to strengthen existing floors. It is fine to use these posts in order to remove the bounce from existing floor joists, provided that they are of an appropriate Prior to ordering, be sure to measure the space from the completed base (concrete footing or appropriately solid landing). Posts can be shifted approximately 6" at a time and the screw at the top is used to adjust smaller distances. There are a lot of posts. These piers are made from steel with sufficient gauge to hold their advertised weight capacities, but are not used as permanent supports for floors like piers on a house. It is always a good idea to check your local building codes before installing so that you can be sure the installation suits your needs. The screws are lubricated and painted with a nice enamel coating, but if they are exposed to heavy moisture, the screws may rust. This product has worked for me in about nine out of ten cases. The majority of the heavy lifting was carried out using a hydraulic jack, and the floor joists were lowered to the posts after they were jacked. As opposed to using the jacks with bars to raise the joists, it is easier to use the lifting pins. They are equipped with a bar that can be turned to adjust the screw and two adjustment pins.
I agree with this product. I just wow- There is no doubt that these support services are beneficial. Since I didn't review them sooner, I feel bad about it. As of now, they've been in their positions for about six It was simple and easy to place the device.
Despite the fact that it is intended for use, I am not making use of this jack. I would have given it a 5-star rating, if I were the one rating it A star. The jack should be fixed to the wall at BOTH ends, preferably with nails or screws. A beam had to be supported in a tough to reach location, and this supported it I have no problem with the smaller pins only the larger ones It is easy for them to slip out. If used in its intended role, the pins would be slipped in, a screw would be screwed into place, nails and fixings would also be nailed into the ground, and the user would never worry about it again.
The work they are doing is what I need My wrap is reaching the level I want it to be The deck (of the house) should be renovated to replace the pillars. 4 - The reason I gave it 5 stars is that I found them at a local store for 27 dollars. A price of $. 00 per item. A lower number. As well as the 6 I purchased here, I purchased 5 from them. (There was also (1) defective product from Amazon. Works, but not as well as it used to.
It is a short lally column for use with jack posts with medium heights. What I love most is the way the top and bottom plates are being welded into place. It would be best if the paint had been applied heavily enough to prevent rust. There are two sizes I bought of these guys. Thanks for the nice talk, Jack.
My jobs I've used them for have all turned out great.
There is a lot of strength and it seems well constructed. A short floor jack was required by me to temporarily lift and support a corner of my 16x18 outdoor deck while I replace a post. This jack was ideal. I went to the hardware store and got my lithium grease at the same time I was getting ready to use it because I knew it would be in place for a few months. A little while later, I noticed it was already nice and There is a lot of strength and it seems well constructed. The cost was well worth it.