QWORK 2 Pack 5" x 1.5" Premium Rubber Wheel with Ball Bearing, Hand Truck Wheel, Capacity up to 88 lbs
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Two wheels have a weight rating of 264 pounds, and one wheel has a weight rating of 132 pounds.
There is a metal hub attached to a solid rubber tire on the wheel
There are six inches of outside diameter on the tire.
A bearing with an ID of 1/2" and a diameter of 1" is included in this package A 3/8" OD hole is needed.
Selected User Reviews For QWORK 2 Pack 5" x 1.5" Premium Rubber Wheel with Ball Bearing, Hand Truck Wheel, Capacity up to 88 lbs
For me who needed the 8" x 2" with, I found it to be a very good deal. The wheels should be 625 bore replacements. What's the reason? 1.
It seemed fair to me that the price was so low. From this perspective, it made sense to me. My options are either to buy a new hand truck for more than $70 or to I have quite a few uses for my hand truck, as you can see. Have had it for more than Even though it could use a paint job, the structural integrity is still 100%. With these great wheels it should last another 20 years. The second paragraph. It is difficult to describe how pleased I am with the quality of these wheels. My jaw dropped when I saw how solid and well constructed they were. Having used these wheels, I can tell they will last for I liked how easy it was to install. All I had to do was sand off the old axles with some sand paper and they were in place. We just wanted to get rid of the old rust and clean them up a little, so I didn't have to use sand paper. I would like to draw your attention to one particular point. Also, I bought the "push nut caps" here on Amazon for a cheap price. New cotter pins were installed to replace the old rusted ones. I think it gives the hand truck a better, more secure feel not only from an aesthetic standpoint.
In conclusion, they state that these wheels can support a maximum load of 580 lbs. These wheels are, in my opinion, worth the investment after buying, inspecting and mounting them. Let me offer some humble insights in the hopes that you will be able to make an.
In this case, I replaced all four wheels with these On my offset smoker, I have steel wheels. scuffed up The maximum depth of the hub has not been specified. According to the advertisement, it is 1GB in size. 75" In fact, the bearing is 2" long, and requires an axle protrusion of at least 2 1/2" so that the retainer and washers can fit properly. The length of my axle is 2 1/4" from the flange to the hole where the cotter pin retainer will go. A thinner wheel would have been a better choice for me if I had known. Even if that were not an issue I would give the product 5 stars. . . I had to spend 40 dollars and an hour to modify the grill in order for these wheels to fit.
In this '5/8" bore wheel Although this seller offers other axle sizes (bearings) other than the standard 7/16 inch ID variety, I find it somewhat irritating that they aren't able to do occasional short runs with 7/16 inch ID bearings pressed into the wheels. There are several edger manufacturers including McLane and Power Trim that are not part of this market segment for Seller. equally good, yet they are ridiculously expensive. Therefore, it is necessary to come up with.
A grey SUV was equipped with these wheels to replace the old ones There is a water holding tank that has broken. It feels as if these are of much greater quality, they feel really solid and reliable. As far as we know, they do not glow There is a small weight penalty, but that is fine with me, mainly I'm looking for how long they will last. Of course, it is still too early to say, but they feel really sturdy.
Earlier this year, I replaced the plastic wheels on my Coleman grill of 8 years old. Wheels of this caliber are very heavy duty. It is important to note that these wheels have half-inch axle holes. I had axles 3/8 inch thick on my grill. glued on a couple washers so that the wheels would stay Getting some bushings would have been a better solution.
This set of wheels was purchased to replace the wheels on our dolly. I think the wheels are going to work well for what they're intended for. Its bearings don't seem smooth, and that's the only complaint I have about them. When they are turned, it feels like they are grinding. They appear to be a well made wheel, aside from that.
After much searching, I found these wheels that both fit and function.
As a result of the improper tire molds, the body of the tire wobbles back and forth, causing it to rub against the carriage's frame.
Related Products For QWORK 2 Pack 5" x 1.5" Premium Rubber Wheel with Ball Bearing, Hand Truck Wheel, Capacity up to 88 lbs
