MIKEDE 10Pack Neodymium Disc Countersunk Hole Magnets 25 LBS, 1.26 inch D x 0.2 inch H Strong Permanent Rare Earth Magnets with 10 Screws
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
There is no way to tell for It's easy to mount the magnets using the screws that came with them. To avoid overtightening the screws, however, it is essential not to over tighten them. Despite being fragile, magnets are hard to work with.
In all honesty, I didn't have to consider the angle, but I did mount at least 20 of these with the same machine screw. Overtightening is something I am more inclined to consider
I don't know
With brass, there is no magnet that will work. Iron is the only material that a magnet can attract. In contrast to (Materials containing iron)
Selected User Reviews For MIKEDE 10Pack Neodymium Disc Countersunk Hole Magnets 25 LBS, 1.26 inch D x 0.2 inch H Strong Permanent Rare Earth Magnets with 10 Screws
My first observation was how tightly packed the magnets were when I opened the package. After I took it out and tried using it to adsorb my objects, I realized that its strong suction was more than enough to fit my needs. Due to their magnetic force, it is important to separate them carefully through the use of view, because their magnetic force is too strong, if the magnets attach to each other, it may prove difficult to separate them.
They are very strong to the point that you wouldn't want to put two of them face to face because it will be a big endeavor to try and separate them. A couple of these are mounted on the sides of my cabinets as tool holders. As a result, I attached some short pieces of wood to enable me to pull them off the surface they are fastened to (like In the past, I've used them as a stop block for my table saw so that I could make repeatable cuts on It is also handy to put them on the refrigerator, and you can put a ton of paper behind it!
I think of the 24 glasses I bought, I have not broken a single one or chipped, cracked or even dipped one In the case of a shed door that doesn't stay closed when the wind blows or the construction of the door prevents it from closing, these magnets will do the trick. Using a magnet on one side and a screwed-on washer on the other side, a door will stay closed even when it is blowing highly. The face of these magnets is where the strength is, the back and sides are not as magnetized as they should be since they are.
Just as electricity needs to be respected, so must they. When you are unconscious and you have one in your hand, trouble can ensue. A magnet and a screwdriver that I had in my hand decided to have an attraction each other as I passed my hand over my work bench. There were several ways it could have turned In my case, it hit from lengthwise, but I was ripped out of my hand and the magnet broke apart. Now I'm one magnet short on my project. The project I used it for was a success.
Having owned three of the magnets, I was so satisfied with their performance that I purchased them again.
I'm writing to give some advice! It's a good idea to be aware of where each magnet is positioned if you separate the magnets. Even just to begin distancing them with a utility knife type blade, they will come together unless there is a plastic separator. are reassembling the magnets, you should use a foam packing container to remove the plastic in between the magnets. After placing the stack of magnets into the ring, add one or even two plastic rings, and THEN place the separated magnet into the ring. Separate magnets will crash into each other as they fall, but the plastic rings will protect them from breaking. The hard-earned experience from my career enables you to benefit from my knowledge.
In addition, I really like the countersunk hole in the middle, so you can mount them anywhere you need them to be. Be careful, the screws are very powerful! (
Assembly instructions provided)
But don't step on them! Having these in your pocket is not what you want to be doing while walking down the street. In a neighborhood like this, you could find yourself sucked across the street, tied to a big truck on your way to the.
It is essential that you do not over-tighten screws/bolts when mounting these magnets. It wasn't a big deal to learn this lesson on the first magnet we used since we had a lot more magnets than we needed. The rest of this package is really handy and I would recommend it.
It would have prevented me from getting 3 blood blisters as a result of You should be careful what you get close to them because they are strong.
One of these magnets provides a stronger grip than a stack of four+ conventional neodymium coin or button magnets, with a greater surface area. If you plan on storing them in an environment where paint will need to be protected, you can use them under a layer of cloth, tape, or plastidip. It is strong enough to be used in an outdoor application or in a space where there is a great deal A full-time position was secured by four of them You can attach a cloth flag to the hood of a vehicle for a two-day event No budge during a two-day off-road event. Due to their large size, you will be able to get enough grip on them even if multiple get stuck directly together. These are strong enough to snap through anything in their way, no matter how big and bulky it is.