Malida Quick Push to Connector, Water Tube Fitting,1/4" Tube OD x 3/8" Tube OD Reducing Straight Union ,for RO Water Systems,Water Purifiers Tube Fittings.
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
In fact, it is required by NFA standards. Also, it is FDA approved, certified, and tested under ASTM standards. A contact with water approved under Section 61 of the Food and Drug Administration. The description does not contain any spoilers.
An insertion point has a tiny pressure ring at the tip that you hold down as you insert the needle. As you pull the tube out, be sure to pull the tube simultaneously. Making it is a very simple process. Pressing down on the pressure ring with the tip of a flat head screwdriver can sometimes help it come out more easily.
Tubes with an outside diameter of 1/4 to 3/8 will probably work
I think a manufacturer would be best suited to answer this question. The only indication of what this could be is on Amazon, where a Tee is shown when used with a 220 psi aquarium A connector should not be trusted at pressures greater than normal water pressure (60 psi to 80 psi)
Selected User Reviews For Malida Quick Push to Connector, Water Tube Fitting,1/4" Tube OD x 3/8" Tube OD Reducing Straight Union ,for RO Water Systems,Water Purifiers Tube Fittings.
A hot water faucet at our kitchen sink provides instant hot water. It is helpful when you would like to have close to boiling water right away instead of having to wait for it to boil. After a while, the faucet decided to stop working for no apparent reason. That's too bad. In order to replace the faulty component, I searched for a replacement and installed it. I thought the connections would be similar, but they were This is what I needed to do to connect these two sections of tubing. It would have been nice to have had a connector that would have allowed me to connect the three tubes together (the old faucet had hot and cold water, the new one just had hot), but I didn't have one that would allow me to connect Yes, the old one might still have been functional, but the end would have been open. The mess under the sink would have been worse than the mess it caused. So after some careful measurements, I headed off to the local home improvement stores to make my purchase. Unfortunately, that didn't work out. A specialized store seemed to be the best option for me. There is still no response. The presence of plumbing stores in a community We did not try them this time, and we were already in quarantine, so they weren't open. The items were found on Amazon after I had conducted a lengthy search. My life would have been much easier had I This was cheaper than ordering a bag of ten, but it was also more expensive. As long as I have the extras on hand, if this happens again I can handle it. In addition, I could use the extra parts to build some kind of terrifying hydraulic contraption that creates fear among my fellow citizens. There are push-in connectors on the connectors Tubes need to be clean and straight and without any deformations in order to work properly. This particular set of adapters goes from 3/8" to 1/4", and I am currently using 1/4" copper tubing to 3/8" tubing (the same as before, but with While you may be able to work these things off, it does require some manual manipulation to accomplish this, so there is no need to worry about them suddenly falling I like the ease of use and tight seal of this product. Occasionally, I will be in need of another one of these, so I am likely to have a difficult time finding the bag with the remaining ones out in the garage. Organizing the garage again is on my to-do list.
You should ensure that you have a flat cut on the end of the item, since they are more picky than similar items. They will leak if they do not. The price is good, and the quality is fair.
It is advertised as clip-free, but in reality, it requires clips (which are included). What matters is that. I think they work just fine. You do need to push in the clip, but it is not a problem. You can even adjust the plumbing with the clips if you need to change the configuration. You can also disassemble them if you use the clip free version, however, you have to push and pull the clips at the same time. the tiny flange on the pipe and pull).
I would give these 4 stars if the lock clips were present, but they are not. They chose badly when it came to these choices. My choices almost always depend on their decisions, but so far they have failed me.
I had to connect some tubing that was different in diameter, and these connectors did a great job.
In spite of the ease of use, this product leaked at each and every.
I received what I expected quickly and according to the description.