Fosmon (2 Pairs) Single Gang Wall Plate, Brush Style Opening Passthrough Cable Plate with Low Voltage Mounting Bracket
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
The white ones are correct.
There is no need to change the cable because this will fit a standard HDTV If you are going through the opposite end of the cable, not the plug, we recommend feeding the opposite end through. I hope this is helpful.
This has an opening through the wall that has been painted with a brush to create a nice appearance
You could run wires through concrete, but how would you do it? What is the point of buying this for concrete if the wires need to be run outside? A drywall patch is better suited for repairing holes in the In order to hang televisions on the wall, I use it to cut holes behind them. Upon cutting the hole, I located a wall outlet near the bottom of the drywall. I then run the cables from the TV through the hole behind it and come out through the hole at the bottom of the stand. This wall plate allows me not to waste too much air conditioning by preventing the holes in the wall from allowing air to leak through. As a result, the drywall looks much better than if it had two holes in it.
Selected User Reviews For Fosmon (2 Pairs) Single Gang Wall Plate, Brush Style Opening Passthrough Cable Plate with Low Voltage Mounting Bracket
In order to complete this installation, two new screws are needed. In order to screw the inside plate to the gang box, you need to remove the inside plate. As a result, the face plate can now be properly aligned and just need to be attached It is possible for a similar installation to be completed at a less expensive cost. Moreover, the seller wasn't economical enough to inform customers that additional screws must be purchased that were not included in the package. You wouldn't want to be embarrassed when you install this box for a client and find out two additional screws are missing because the seller didn't inform the customer.
This product was titled "Fosmon Single Gang Wall Plate 2 Piece, Brush Style Opening Passthrough Cable Plate with Low Voltage Mounting Bracket" at the time I purchased it. When you need to install these, you typically need two sets to complete the job. It took me a few seconds to see that the title was "2 Piece" which is a clever way of saying that this consists of two separate parts. Maybe I should have paid more attention to the pictures, but there are similar products on the market that do not rely on such deceptive If I had purchased the 2- in one, I would have saved a lot of money It would have been $1 or $2 more for another vendor who was actually going to provide two pieces. I received an automated email from the company informing me that they oppose my issue. So, I replied to them explaining why. By stating this I am hoping to prevent someone else from making the same assumption as I did when they used the same descriptions as others providing 2 complete sets, not just the two.
The only reason I lowered the star rating is because of the It is important to clearly state that the included instructions were for a completely different application of the faceplate so they are entirely Additionally, as mentioned by others, I believe that a cheap cardboard template could have been included so that you could trace the cutout you're There's nothing rocket science about it simply a few details that would help to make the entire installation process easier and faster. This gang box concept is really awesome since it is not only fairly easy to fix, but it is also easy to cut a bigger hole with, and it also holds very well to the drywall. Before I replaced the accompanying wall-plate with this type of faceplate, I used to purchase this type of faceplate Use the toggle screws with the wing type to mount the faceplate on the I had to do a little extra work, but once I did it, I no longer had to worry about my faceplates loosening and falling off when I added or replaced It is mandatory that you take apart the faceplate after installing the gang box and attach the center piece to the gang box with the long screws provided after the installation has been completed. After you have pulled your cables through, you must attach the outer portion of the faceplate to the center using the short screws that came with it. This is completed.
My recommendation is to purchase a different brand altogether since this product is very poor. It is not only that the gang screws snap when screwed into place, but the brush plate that they supply to go along with them DOES NOT fit with the screws they send. It is not safe to use the screws. In the near future I will replace this item with a higher quality one, since the rigging procedure was completely involved.
There are no proper screws to attach the plates to the boxes, so the plates fall off the walls despite the decent quality of the product. In addition, the holes on the plates do not allow screws to be used in the boxes. Instead, they line up with the sheetrock on the outside of the boxes, rendering them My next step might be to purchase some sheetrock screws with nice heads to fix this problem.
My set of 5 wall plates and mounting brackets came from Amazon rather than my local big-chain hardware store, and I was pleased with the service. Despite having paid for the set of 5 on Amazon, I was only able to get two after going to the depot this weekend for I am only allowed to pick up one. The sets there are five. It was differing brands and you could argue that the building materials were different as well, but I really couldn't differentiate them from each other. I found the mounting brackets and wall plate from Fosmon to be pretty sturdy. It was hard to snap the wall plate with my hands without some effort.
The only downside to the set versus what you get at the store was the lack of a paper template or stencil to cut on the wall. Unlike the store brand one, this one was packaged with a template on the cardboard backing. I had to make mine from scratch. By this, I mean I traced the pattern onto the cardboard box Amazon shipped this in, put the mounting bracket on it, and used that as the basis for mounting. This was a perfectly acceptable decision considering how much I would have saved on the product. I would recommend this product to others who had similar needs for the product.
I was not happy with the quality of the cable hider because it was a bit thick. It would be nice if there were instructions on getting the brush pass-through installed (you have to remove the front panel from the brush pass-through first and install on gang box, then install the front panel again) but since I am handy, I was certainly able to figure it out. In addition, the price could have been a few dollars lower, as you can get a regular gang box and plate for half the price. That is the reason why it only received four I find this product to be outstanding again.
Will Robinson, you are being warned. Please be aware. The header of this item indicates that it is a 4-pack, not a 3-pack. These two items come in a The count seems to be part and parcel. This is false. That's a very misleading statement, however they could be counting parts instead of screws, which would mean they missed counting them. It would be an 8 pack if there were 8 of them. "I do not believe in you, These two items come in a The total number of units is two. In my opinion, they had a good reason for doing this. I have it in front of you. The large print of the product appears to indicate that this is a 4 pack, but the small print lower on into the area states that two cover plates plus two mounting brackets make this product a 4. My name is Dummy in the mirror. Let me think about it and then I'll check in the bathroom. (Were it not for negligence, I would have been missing that. )
It looks like it does due to my failure
So just to back up their bad morals, PLEASE BUY A 2ND UNIT, NOT THIS ONE.