OIMERRY Plastic Welder Kit with 800pcs Hot Staples, 110V Hot Stapler Bumper Plastic Repair Welding Kit
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
As for the staples, they heat up relatively quickly. The rate of heating depends on the heating setting and the diameter of the staples. I would like 6mm to be the minimum. It varies depending on the type and size of the staple (8mm), usually it is between 4 and 8 seconds, and the staple is literally red hot!
It will work, but a liquid proof seal will not be formed unless it is made of thermoplastic. However, fuel can still leak out of the crack because it only mechanically secures the two sides.
What did you do with the switch at the back of the unit?
On the back of the unit, make sure it is switched on. What happens when the switch is turned on? You may need to check the outlet on your socket If the outlet doesn't appear to be working, test it with a radio or a light. After the rear switch is on and lit, you turn on the unit at the front, and then select the power level you want. The manufacturer should be contacted if all else fails. In my opinion, it would be best to pull the unit apart, although doing so may void the All the best to you.
Selected User Reviews For OIMERRY Plastic Welder Kit with 800pcs Hot Staples, 110V Hot Stapler Bumper Plastic Repair Welding Kit
Dashboards, mower hoods, and plastic gas caps are all repaired by us. Over the past few months, I have installed hundreds of staples/clips. All the clips are nice, the case is nice, the assortment of clips is good, and the quality of everything is great. A very well built product. One con, however, is that the end fly is cut off and leaves behind a They must be bent to round off the ends without the point, but it takes a while to bend them, so it is not suitable for production work. They must also have holes in the handle at 45 degrees for clips that are not drilled the same, one at 45 and one at 90 degrees. Making it difficult to hold clips in place. It is very difficult to find a con. This thing is the bomb for the money! Buying another one would be the quickest thing I would do if it died tomorrow. The other plastic welders that I've tried can't compare to this one. In order to keep the plastic together, it fuses it together and reinforces it with wire. I love it. As a Tip, if possible do the repair from the backside of the garment. This will give the impression that it has been stitched in. Overall, I would rate this plastic welder as a 5 STAR product. Despite a few negatives, the positives outweigh the.
There are several reviews for this hot stapler as there are for the other one. There is only one difference between the two this hot stapler includes 800 staples and the other one only 600. This item was used to replace the bumper cover of a BMW. It There are adjustable temperature settings on the gun, as well as a low profile so that it can fit in Staples were available in a good assortment. As you can see from the picture, the staples were slightly difficult to align in the gun due to the small holes, but I will become more proficient at this method over time. The staples heated very quickly when the trigger was pushed It is important to finish the staple with a twist at the end to ensure it will be properly anchored. Although I deduct 1 star from my rating, I am pleased with my purchase My one star is based on the fact that the contact information for the manufacturer is not listed in the instruction booklet for warranty or support. In addition, the instructions booklet is identical to the one that came with the other Amazon device I originally bought and promptly.
This machine has a quick heat up and is easy to use. The digital control dial is more reliable than just a regular rheostat knob. The staples are accessed through a handy storage box that comes with it. However, it would be nice if there were more compartments to store A nice set of staples is provided for you to start with. My plastic engine guard, which had cracked around the bolt holes, was repaired and worked perfectly. I can't wait to use it again in the future.
In addition to fixing plastics on an ATV and a cracked cowl cover on my truck, I used this stapler/welder. I was pleased with the welder's performance. My staples were applied first, and then I used a welder to fill the crack, then I sanded it. We had trouble using the temp controls, but the temperature controls were easy to operate. The painted plastic on the ATV was repainted and you couldn't tell where it had been repaired. Stapling on both sides becomes more durable when they are welded after. It is a great tool for repair work. It is recommended.
This is an incredible product. I love the built-in display. It is bright and adjustable. It feels high quality and is well made. My laptop is heating up to the highest setting in seconds. The other staplers I've had cost more, and they were of worse quality. The following tools are included in the toolbox Simple and cheap are not important factors for me, I am more concerned with the tooling, and they did a beautiful job*
Accessories It comes with a TON of staples that I will not even be able to go through in five years. My experience has shown that staples can be cut quite well using snaps, but not with the right ones. To cut them, you should use pig hoof plier snips since you can get in more places and push them closer to each other. In general
Here are more like tile fragments
Overall The purchase turned out to be great, and I have done bodywork professionally for 12 years now, so I would give it a 10/10.
The cover of a plastic bumper was repaired with this. I think so far the system is working great. The staples are heated quickly and it's easy to place the staples exactly where you want them to be. Stapling will take place from the back, and grinding and plastic welding will take place Although the bumper is already pretty solid, it will be even better in the future. In the long run, it will be interesting to see how this machine holds up If there is an option to update, I'd be happy to do so.
For my shop, I bought this. A great stapler, used it to repair the console of a 1994 Jeep, and it worked great, had a wide range of heat, so I was able to control it completely at all times. This would be a great tool for anyone who has to work on late-model vehicles.