US JACK D-41610 6 Ton Garage Stands 100% Made in USA

$ 249.00

Score By Feature

Based on 33 ratings

Sturdiness

9.50

Safety Features

9.60

Lock Feature

9.80

OveReview Final Score

How Our Score Is Calculated

Product Description

All products are made in the United States

The low height is 16 1/4 " and the maximum height is 25 1/4 " The base diameter is

Questions & Answers

Let me make sure you understand According to the listing, this product includes 2 stands, is that right?

They were shipped as a pair in 2016 to me, and I just received them today. Inside the box, there are two stands. It looks like the welds and paint are in good shape. There is a lot of care taken to wrap the top and bottom of each stand in stretch type plastic wrap, and the container they were shipped in is about as thick and as sturdy as it gets. The first time I used them was a few months ago, but I'm eager to try them again. They have a low height of just over 16 inches when they are first built, which makes them tall to begin with.

Does each of these pass the ASME test Do you know what the 2014 ratings were?

Go back to their web page. This is the answer I found, nonetheless. You can see the bow in this picture. The 6 ton jack I have is well-suited to the job. They are tall, which is the only negative thing about the 6 tons. My lower cars are difficult to fit in them, but I use them for my LRV and truck. The "SAFETY WARNINGS" section on the back of the carton U. OPERATING PROPERLY IS KEY. Jack stands from Jack Company are included in the service of vehicles at predetermined heights and used in pairs to support one end of the vehicle. The jack stands do not have the means for raising the stand Lowering the vehicle is a good thing. The ASME PASE - 2008 standard is complied with by our stands This standard describes safety standards for portable automotive service equipment in 2014. **Breathe in a little* Ensure that you use matched pairs It is only recommended to use this stand in pairs instead of as a single stand. Please note During the test period, the maximum load capacity for each matched pair shall not exceed the rated capacity of the individual stand. Rated capacity is per pair and not per stand. The stand should be used to support only one end of the vehicle. There should not be a need to support a vehicle on both ends simultaneously when using stands. Please note Make sure the surface is hard, level, and clean. Please note Stack the load on the saddle in the middle. Please note There may not be any alterations made to this product*. It is possible to suffer personal injury and/ or property damage if you do not heed these safety warnings.

Selected User Reviews For US JACK D-41610 6 Ton Garage Stands 100% Made in USA

There is no way you can go wrong with What these things are are The piece looks good, it's well made, and it's solid

5/5

The love I have for them is more than I have for all of my exgirlfriends combined, but not as much as I do for.

Bria Conner

| May 21, 2021

This product is made in Michigan in the United States! It's a good thing these are heavy duty jack stands, I intend to buy another set each of 6 tons

5/5

Can get almost 24 inches from a low position. Thus you can lift a car to its maximum height. Thanks for the extra wide foot print. It will greatly improve the stability of a car or truck on a stand.

Emmeline Garrison

| Aug 10, 2020

The product is well made Under, you can feel safe

5/5

Jack stands made in America are of great quality. It makes me feel much safer to park my '68 Chrysler or any other vehicle under this cover. My opinion is they're good and I.

Edgar Duncan

| Aug 31, 2020

There isn't much to say other than that

5/5

There's really only one thing I need to say 'These 6 ton garage floors are like a Swiss Army knife. We provide high quality, heavy-duty jacks that are made in the USA. The title says it all 'Nuff said!.

Adam Mejia

| Jul 01, 2021

In what capacity is ED involved Does it make sense to cut corners on stands when you pay cost? In the middle of a maintenance job underneath my Jeep Wrangler underneath $30 Torins, I decided my life was worth more than that

5/5

I found that these stand have no wobble like cheaper stands, and they support the front axle of my Jeep very well.

Rosemary Bullock

| Oct 26, 2020

Making in the USA is now a serious issue for me, as my life is worth more than the 150 dollar deviation! It is strong

5/5

A great extension of height. Easy to do with 24" wide. There are two locking points on each perch. As easy as it is to retract a Made in China stand, retracting is not for everyone. When the arm is lifted without much weight attached, China Stands retrace when the arm is lifted. They have advantages and disadvantages. In order to retract US Jacks, you need to lift up on the black leg and then lift the handle. You will need two hands to retract. However, SAFE is the most important thing. I'm about to need to buy my last set of jack stands.

Blaze Reilly

| Apr 13, 2021

A will has been drafted for them

5/5

The price isn't cheap, but the value is worth it. Spend some time looking for some good ones instead of the cheap You won't have to worry about your health with these jacks, they're solid and are going to.

Angelo Church

| Jul 16, 2021

5/5

0 out of 5. I have never seen a floor jack of this quality before. This is a very stable system. It was solid as You can use these without any worries.