Oznium Brightest Light Bolt - Flush Mount 12V LED Light for Bumper, Grille, Cars Interior, Dash, Ambient Lighting, Motorcycle w/Sleek Aluminum Housing & Screw Nut (6 mm Black, Red LED)

When I don't make an aggressive turn, I have a habit of not hearing the blinker stay on. My Toyota RAV4 had the problem of being Deaf-proof, so I decided to fix the issue. The following LED Amber lights were located after searching for small Amber LED lights. It appeared to be a good fit for what I was trying to accomplish. The speakers you pictured are just above, in front of, and behind my audio tweeters on each door (basically behind the side view mirrors). As shown above). As a result, I can now see the flashing light whenever the blinkers are still on, even if I don't hear them. As a deaf person (75%), I probably should have taken this step earlier. No more driving down the road while a turn signal is During the day, the idea was only intended for use during daylight hours. While driving at night, I have occasionally seen flashing arrows on the instrument cluster housing (steering wheel and hand placement blocks quite a bit Its lights are as good at night as they are during the day. I plan to buy this brand again for a project I have coming up It is not overly bright and there is good dispersion of light. I was deaf-proof and I can't hear you.

Koda Nunez

| Aug 02, 2021

Their work is beautiful, and I love it! Be careful when you take a look at how tiny and compact these things are they pack a punch! In order to test and determine the size and where they should be used in my car, I bought one LED of each size (6, 11, and 16mm) in the blue color first. As a result, I had to wait for the sun to set and purchase a 12v cigarette lighter adapter to power the lights externally. I then taped the lights on my car inside where I'd like them to be. The 6mm ones are so small, this also made it easier for them to be installed and hidden from sight since they are so small. The LED bolts of 6mm finally won out and I installed seven of them My four doors each have one, the two cup holders in the front, and the center cubbyhole under the dash each have one. When I found how many LEDs per 6mm spot I needed and where each one should go, I had them professionally installed and am overjoyed with how they turned out! Particularly in the doors) fade off after a few minutes if the engine is turned off or if I lock the doors as I exit the vehicle. I find this tiny LED bolts to be very difficult to work with because of how small the "lip" around the light's source is. As for the drill bit, I bought the 6mm one from Oznium, but the "lip" that is meant to hold and prevent the LED from slipping out of the hole is so thin I didn't trust it to do the job. Therefore, if there is one piece of advice for improvement, it would be to make the lip a bit bigger to ease your Because of that, I was able to buy rubber washers from my local hardware store that fit very snugly and securely around the bolts so that there was no way the LEDs could slip through. To see them in action, you can view the video attached. I have attached the following images The 6mm LED bolts were used as a "test phase" after they were powered for 1 hour through a cigarette lighter adapter, then I taped them around my car to see how many and where they should be placed. After which, I drove around at night with taped and turned-on headphones, in order to ensure they wouldn't distract me from I was able to proceed with permanent installation after trying different quantities and placing them in the right spots.

Luciano Payne

| May 16, 2021

It can be challenging to install. A new update (7/2018) is available. On the truck, about four months after it was delivered, one of the lights has lost its black paint. A copper color is now displayed. I don't think it will affect them too much. The one that has lost its paint leaves a little to be desired, but when the lights are on, it is hard to tell the difference in color. My light must be defective, and I will need to order another one. Due to deterioration in quality and durability, two stars were taken away from the rating. On my 2017 Tundra, I just mounted the lights in the grille. As you can see, I have a different grille than a typical Tundra, it's an X-frame Spectacular grille for an SP vehicle. In reading the description of the 11mm amber lights, I was concerned that they were clear, as the lights are amber in color. But when they are turned on, those cameras emit a bright amber glow. In addition to the lights themselves, LED turn-signal lights are built well and should last. I tapped the DRLs into the LEDs, so they come on when the LEDs are on, and turn off when the LEDs are I believe that the wiring on the lights is quite thin, probably about 26 gauge, but the lights draw very little power, so you shouldn't have to install a much larger fuse on anything you connect them to. It was necessary for me to remove the grille in order to get to everything. If you install them in this manner, I highly recommend getting a second pair of hands to assist you. In order to make sure the lights did not fall through the grille holes, I used larger washers. The washers are so tiny that you can't even see them when the lights are on. It took me a while to install these mods since I had little experience installing mods of this sort. I did it, but it took a lot of time. It would have taken us about four hours to arrange everything for these parts if I hadn't had to run to the store three times to find the right ones. Installing them definitely would have taken me (us) about two hours. I gave them five stars because the lights themselves are amazing, so the battery life is five hours. In this type of application, however, be prepared to spend a day installing them.

Amoura Hoover

| Dec 19, 2020

My purpose in purchasing this was to install it in the console area on the floorboard of my Ram truck. It is an amazingly strong and bright little light. The light was too bright, and I had to cover it with a small piece of window film. You've made it look perfect now! The following installation tips are provided for your convenience Please note
This must not be installed in an area where the light will shine directly towards your eyes, it is very bright. Please note
Simply connect the outlet plug to the outlet that shuts off with the car if you want the light on while the car is on. Please note
A straight razor blade can be used to cut a bit of insulation from the two wires that feed the plug (hot and ground). You can see copper wires as soon as you reach them. Please note
This trim area must be offset from the ground so that no power can reach it. Please note
Taking the bare ends of the wires, strip them of 1" and wrap them around the two trimmed areas. Please note
To ensure that the light works, you should turn On the key and ensure the polarity is correct. Please note
The key needs to be turned off before you can solder the wires, then tape the soldered wires.

Paisleigh Copeland

| Jul 01, 2021