MUYI 5 Sets 18AWG Waterproof Electrical Connectors Kit 1.5mm Series Terminal and Rubber Seal with 10cm Wire Weatherpack Connectors (4 pin)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
I'm delighted to meet you and happy to hear from you today. Regarding your case, we believe you should order the 4-pin set and the 2-pin set. In this case, we group their five kits into a package, and we do not sell the kits separately. My sincere hope is that you will understand. If you have any other questions, please email us, we wish you a great day IKEA MUYI STORE
I believe that the wires are made of
I hope you're having a good day, my friend! We can provide you with the following details about the connector in your case Approximately 4mm wide (male side) is the width of the plugs. 1 inch/4 cm. The number 73 There are two sizes of plugs one and two. Measure 2 cm/0. 47" in length. The plugs are standardized in the following way (feminine side) 1 inch/8 cm. The 5th A height of zero is indicated by the plugs. I'm 7 cm/0. 28" in length. I hope this helps! Thanks a lot and have a great day. IKEA MUYI STORE
I hope you're having a good day, my friend! To answer your question, we wish to emphasize that this type of waterproof connector is not designed for use in water It is constructed with 18 gauge wire and has a maximum current of Three A's. I hope this helps! We will do our best to assist in any other questions you may have. Feel free to email us! I am sending my best regards, I SHOPPED AT THE SOLUTION
Selected User Reviews For MUYI 5 Sets 18AWG Waterproof Electrical Connectors Kit 1.5mm Series Terminal and Rubber Seal with 10cm Wire Weatherpack Connectors (4 pin)
You can rest assured that these are not rated for use in warm areas. They are mounted on the inner fender of my engine compartment just in front of the intake manifold. There is no particularly hot weather in that part of the country. About 16 inches from the engine, these things stay in a state that is close to melting, but they are not molten altogether. At the moment, my body temperature is about 130 °F -140F (55-57 60 degrees Fahrenheit) Due to the length of time I spent on this project, I'm going to have to scrap it. ALSO, some of the wire colors on the connectors didn't line up. Due to the fact that I was color-coding my wiring (I got spools of wire spools in matching colors), creating this circuit was more difficult than I expected. This should be possible when the connectors are clearly labeled with colors, however the quality control is apparently poor. This could have been the cause of severe cross wiring issues. As they provide a rubber seal as well as a waterproof connector, it appears that quality should be there. However, these are not very good connectors simply because they are The quality control is poor, and it is not good in warm climates (even below the 176 F/80C rating).
Recently, I had an issue with one of the connectors when I used them to wire up a light. In the course of troubleshooting for about an hour, I discovered that the actual problem was the fact that the A portion of the tail wire for one of the connectors did not make contact with the molded plastic at the Unfortunately, it was also the ground, so I couldn't get anything to work! As it turned out, I had to pull the connector out of the connector and replace it The wire must be soldered to the The first time you connect a brand new connector, you would expect this to be unnecessary. Our recommendation is Make sure each pin and wire are working correctly before using each connector you can save lots of time this way!.
By using these plugs, I used only one cut to the existing wiring harness on my polaris ranger in order to create a fuel pump kill switch system. With this feature, I can now kill the fuel pump to prevent anyone from simply driving off with my machine without knowing where the kill switch is. I love it.
As far as the quality of the four I purchased for my motorcycle that needs water sealing is concerned, I am very satisfied!.
These are large connectors that seem pretty robust. I did not use them in a wet environment, but I chose them because they are 18AWG. It took me over a week to use all of the 12 sets of 5 that I ordered. A small problem arises from coding the wires since the wires are arranged in a 1X4 pattern).
If you want to keep them dry, do not expose them to water. They form a very snug seal around the gasketted This is a good product.
Although I have only installed these, I cannot comment on their durability as I have yet to use them. However, they seem very durable and weatherproof from the look and feel of them. It would be a pleasure to work with I installed them on the front end of my Chrysler 300 where they will be exposed to all kinds of weather.
The connectors are of good quality. Since I hate having to rely on a connector that is weak, I chose to purchase the four-lead version instead of the two-lead version and simply paralleled two of each lead so I could have greater current capacity. In the end these connectors were well built enough that the two lead version would have worked fine. I thought my money was well spent.