GM Genuine Parts 12679524 Fuel Injection Throttle Body with Throttle Actuator
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Not sure if I have a 5 or 6. An eight-cylinder engine with a displacement of 3 liters.
Please note In the event that DTCs are present, do not perform this procedure. The following would not be possible without a scanning software How to Learn Procedure Put the engine into PARK for 3 minutes, then start and idle it again. The following two points are important to note. Make sure you monitor the desired and actual RPMs with a scan tool. 1. *br> 2. It is expected that the ECM will begin to learn about the new idle cells and the Desired RPM will drop. The following instructions apply to 4 and In the next 60 seconds, turn off the ignition. The fifth point is the most important one. Put the engine into PARK for 3 minutes, then start and idle it again. I hope you like my phrasing as well. By the end of the 3 minute run time, the engine should be idling normally. It is important that you know the following When the check engine light comes on during a drive cycle, DTCs related to idle speed may also be present. It is recommended that you clear idle speed codes to allow the ECM to continue learning. When the idle speed of the engine has not been learned, it will be necessary for the vehicle to be driven at speeds above 70 km/h (44 mph), with several decelerations. The following information is supplied by SpeakFreely.com. It is important that the engine idles normally after the drive cycle. You must turn off the ignition for 60 seconds in order for the engine idle speed to be learned, so repeat steps 6 if it hasn't been learned. Item 8 has no meaning unless it is translated into English. Clear any DTCs and return to the diagnostic that referred you here once the engine speed has returned to normal.
The analog signal
Although I'm not sure of the bolt pattern, it was 4 The size of the print area is 1/8" by 2" A center hole to center hole distance of 3" high.
Selected User Reviews For GM Genuine Parts 12679524 Fuel Injection Throttle Body with Throttle Actuator
On our 2008 suburban, the throttle body on this vehicle failed catastrophically, and the dealer quoted us more than $700 for the service. A relatively short period of time, the throttle was totally non-responsive. It would idle and not After installing everything and putting all the plastic back together, it took us less than 10 minutes. In addition, we put a new AC Delco gasket in. It was an unnecessary waste of time and money. The old gasket was still good
Now this is where it gets tough. The last time I did this job was on a late model Chevy. In the absence of a scan tool, the idle relearn procedure is a real pain in the neck. YouTube may make it seem easy, but it is never that easy. Driving and idling have been required for several days to allow the idle rates on both vehicles to return to normal. You should remove your negative battery cable and hold it on your positive terminal for the length of time it takes to relearn your battery. Even after a week or two, it still does not fix it, but it sure helps! Although eventually the idle speed will drop back down, it remains an inconvenience. Do not, in addition, do what I did and wait for the first snow of the year to deal with it. My decision to drive "in excess of 44 mph with multiple acceleration and deceleration cycles" as I was instructed in several inches of snow, at night, with headlights on and active ABS, and with an empty gas tank, was not the best. It all comes down to this. While the repair itself is relatively simple, parts on Amazon are cheaper than retailer parts (duh) and relearn is likely to be a challenge for the average Joe, but not impossible. Also, if you have a high mileage car, expect to break your PCV hose on this job, and buy a new one before you try it. Like me, you can also use 3/8" radiator hose if you are in a hurry. (1/2" would be preferable.
I bought this for my 2007 Chevy Tahoe and it fit perfectly. The throttle position sensor was giving me a code. Rather than replacing just the sensor part, it was decided to replace the whole device instead. I'm going to give you a witchy It took me no more than 20 minutes to get back on my feet. Other reviews noted that there was no code, so smoother ideals were to be expected. In order to replace the battery, I disconnected it first. br>It's easy to relearn by watching YouTube videos or searching the web.
You can find instructions on how to accomplish this all over the internet, so it shouldn't be that hard to figure out!.
A noise was made by the actuator on the throttle, and I knew what was going to happen. It was easy to get the part number off the original part and buy it. It was impossible to beat the prices at the dealer even at wholesale cost, and I work for a.
When installed in a 2007 Escalade, it works great, but you will need to relearn how to control the throttle. After this is installed on your vehicle, you will be unable to drive if you don't have a high-end TDS programmer. It was very frustrating to have to remove it, drive to a dealership and have it put back There is a catch here I don't know if it applies to every car, but it does for 2007-2011 Results of the 2011 General Meetings.
It fit perfectly. I am happy with how things have gone so far. This is a very simple procedure The most likely course of action will be to resubmit Replace the old gasket with the old one. This is a heavy duty item. The design is clearly intended to be swapped frequently. How to get the computer to re-start It was a little tedious to learn idle. It is best to let the truck warm up completely before beginning this.
Replacing the original GM part worked very well on the 2007 GMC Yukon XL Flexfuel, last part had a light warp that caused the vacuum leak during cold weather starts. This solved the problem for a much lower price than a dealer replacement and was easy to install I suggest also investing in and using a new gasket to ensure a good seal.
This car works well, but it will take the computer about 100 miles to adjust. During rain or snow, it will not adjust properly as it needs to stop for at least a few minutes.