Quadra Fire Castile, Sante Fe, and Contour Combustion Exhaust Motor Kit 812-4400
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
The pel pro products I have used these on
Let's do it I'm not sure
This piece of machinery is not the right motor for your stove. The correct Motor and Housing to use is # 812-F.
Selected User Reviews For Quadra Fire Castile, Sante Fe, and Contour Combustion Exhaust Motor Kit 812-4400
I found this blower to be an exact replacement for the original OEM part. When installed, I learned how quiet the fan and stove were when I first purchased the stove. After the blower motor was installed eight years ago, I think we did well. Over the last two years I have thoroughly cleaned the stove twice, and I remove the upper and rear plates twice a year to prevent ashes from gathering where the exhaust fan is located. The burner motor and blower on the Castile stove were fairly straightforward to replace. Quadra-Scan can be used when According to the oven instructions, it is necessary to remove three additional screws from the back cover in addition to the four already mentioned in the oven setup. In addition, the ground wire on the power outlet plug needs to be disconnected from the stove, which is not Separate the vacuum hose does not need to be done. A 1/4" socket and a ratchet can be used to loosen the six hex head screws needed to remove the exhaust fan, and the gasket came off easily with a vacuum and In order to replace the gasket, the screws will need to be removed. There was an 8-volt battery that needed replacing Corroded screws of this size were used, since the originals were 3" long. A connector kit is provided with the fan/blower so that male and female connectors can be used. As a result, the male was disconnected from the new blower, and the female was connected, in case I wanted to replace it with a Quadra-blade In the future, a fire blower will be used. To secure the new gasket that came with the fan/motor on the stove, I secured it with two screws. After installing the fan/blower, I turned it on. My first action was to start the other screws, and then tighten The rest of the inside of the stove was thoroughly cleaned while it was open, as well as the circulation blower assembly since I hadn't done it in a while. This new Quadra-C will be examined in time to see if it will last as long as the original This unit is for fires.
In a nutshell, Here are some things to be thankful for I am - fit into my Castile stove very well
The bad I am - Rather than the 13-inch fan being quiet, I received a defective one that made more noise The year is This fan had failed and had to be replaced (see video attached)
- There are about a quarter as many impeller blades on the new fan compared to the original. **The Bad I am - It turned out that the electrical connectors we used for our QuadraFire Castile were not appropriate. It is a very brittle gasket material
Take extra care when installing on QuadraFire Castile stoves
Bottom Line NOT recommended.
This blower I bought on December 15, 2017 for use as a standby and it has sat on a shelf in the box it came in until just two days ago when I needed it. Since I replaced my exhaust blowers about three to five years ago, I know how long they last. Originally, I used the old blow until it started making noise so I changed it. In addition to making more noise than the old one, the new one sounded as if the fan was striking the backing plate, and that is what it actually did. The iron cover was removed from the inside of the stove and I checked the fan. A wear mark was visible where the fan was rubbing on the It is impossible for a fan to be mounted on the motor shaft because it has end-to-end play, which causes a fan to catch on the backing plate when it is mounted. Since I didn't want to extract the motor yet due to lack of heat and the fact that the fan is made of light tin, I bent the fins out very gently to make sure they cleared the backing board when the shaft was pushed I have no complaints right now, although it sometimes makes a slight noise but it is much better than having to deal with the noise when it was being In the meantime, I keep a fan handy, since they always go out when it's cold and I do not want to get a new one. If I buy this again in the future, I have got to think about it.
'The motor and backing plate fit very well. It appears that they are identical to the originals. original fan blade was cleaned and reused as the one included in the kit is smaller, lighter, and seems to be built much differently than the one that came with the kit. There were no holes in the gasket supplied for the screws holding the backing plate in place. You can use the new backing plate as a template and cut the holes with an exact knife. Then put the backing plate over the screws so it stays in place, and then As a matter of fact, until the cabinet was separated from the walls, it was the hardest part of the job.
The exhaust blower in my Quadra-Wife had to be replaced There has been a fire in I am replacing myself for the second time. Despite the fact that it was rebuilt, it came with a reusable silicone Quadra-Power has recommended the same exact model number for this new blower as the old one and it seems to be quieter I was very pleased with the fit of the mounting plate and gasket. Although the vendor informed me about the slight delay in shipping, the package arrived on time. As a result of my purchase, I am very pleased with it and would recommend it.
That was such a wonderful surprise! It enhanced my Christmas day! Following up on the service It was outstanding that my order was followed through on and the gaskets I ordered were delivered with it.
Due to the fact that this is the part that was listed in the stove's manual, I ordered it. Due to the fact that half of the stove had to be disassembled, it took several hours to replace. I had to scrape the old gasket out, which was a little messy. Therefore, I had a vacuum on hand to clean out both the mess and the back of the I didn't have any trouble replacing it, but it took a long time. It is working well and should not have any problems in the foreseeable future. It is important if this is your first time replacing various electrical components to take note of how the wires are connected, keep track of all the screws, and if you go with a shortcut if they must be risked damaging the control unit and vacuum switch.