Front Lip ,HengJia Auto Parts 2.5m/8.2ft Car carbon fiber front lip,Front Bumper Lip ,Carbon Lip ,Side Skirt, front lip spoiler 100% waterproof protection(Carbon black)

If you open this product, you will be confronted with an obnoxious chemical smell. It should dry out in a few days if you lay it flat in an unoccupied room. It mostly goes away after a few days. In the installation instructions, there was a Thai section. I'm kidding, but there's a picture of it.

I had to clean the underside thoroughly with wipes, soap, water, and alcohol. It may take some time, but it is essential to clean it. You will have troubles sticking to a dirty surface, so don't be mad if it falls off later because you were too lazy to invest the extra $5 Spend 10 minutes really cleaning the underside of the mattress. ) It comes with two adhesive promo cards, but it should have come with three. Adhesion requires that they dry quickly, but they are essential for allowing adhesion. While it does take some time to measure and cut out the "triangles" for the bends, it is worth the effort. Marking the red tape with a pen to estimate where the bends are and then mapping the triangles from there was all I had to do. Further, you'll have to stretch the lip so that it bends. There's not a lot of elastic in the lip, it's rubber. In addition, you may also want to cut the triangles with utility scissors. Since the rubber is thick enough, I am unsure that normal scissors will cut through it. Two hands were required for me to slam the scissors down on the The Lip Application has already been 3 days since it was applied. That's a good sign that he hasn't fallen off. In addition, I haven't yet put the screws on but I will probably do so later today. However, I am not brave enough to put it through a car wash yet, so I will send an update once that is completed. I like it so far all in all. If the front lip lasts through a car wash, I will consider buying two more for the side skirts. It's great that it's rubber because a real lip kit would make me cry if I cracked it. This update (4/3/18) is in Taking fourth automatic car wash and driving through a few thunderstorms later, the front lip is still on. Neither the screws nor the anchors have been installed yet. Please read the following New Update There is still a lip on the front. A couple of screws had to be added to one of the bends since it was starting to fall off at the corner. ' (This was also where I had to cut "triangles" to bend it. a) The screws were installed recently in January. As of 2019, the lip appears to have held up well. Unfortunately, I didn't have time to safely swerve or brake safely at highway speeds, and the front lip was damaged by old debris from a blown tire. The car in front of me kicked it up so fast that I wasn't able to avoid the damage. Even in the worst of circumstances, the poor car managed to keep going. As strange as it sounds, the lip is still attached. On the other hand, the center of the lip split horizontally in the middle, where it meets the adhesive part. There is a good chance I'll have to replace it at some point as rubber will degrade, widening the gap further. Despite this, I will get another three at a later date. I will give the front lip a makeover as well as Please see the following updated version from today There is still a lip on the original! A small portion of the adhesive is wearing off near the wheel well, but it is still in good condition considering it was applied two years ago. The Velcro keeps it in place for now since I grew lazy. Although the split in the middle has widened, it is still safe to drive on. I ran it through the car wash well over 30 It is reasonably well kept, though some graphics have worn off or scratched off, but all things considered, it is still fine.

Blaze Archer

| Mar 12, 2021

I wish it had a strong adhesive for installation. It looks great, but I wish it were stronger! In order to secure it to the bumper, I had to use small screws and washers. As for me, I like it on my Tesla Model S. It.

Remington Donahue

| May 07, 2021

A must-have I think for anyone who is in need of an inexpensive upgrade for their theft vehicle! The rubber is great, it looks terrific, and the carbon fiber is an added bonus.

Emanuel Stephenson

| Mar 17, 2021

I only had a problem with the tape that came with it. Nonetheless, I used my 3M tape to glue it on and it worked just fine. Overall, it looks fine.

Blake Zimmerman

| Jul 28, 2020

The system was installed on a 2009 Honda Accord that was equipped with the V6 Ex-periment A decent amount of difficulty was involved in installation. This bumper needs some cutting to make it stick more solidly and bend more easily. This product is made from high quality and sturdy materials. With this kit you can add more lasting hold by using the 6 screws that go through your bumper (I added some of my own too). It's a bit hard to tell if the screws are necessary, but since it's on the bottom front end of my car, I decided to play it safe by adding them. I think it brings the front of the car down to a whole new level thanks to this small, subtle change! The next time I need a vehicle I would purchase again. br>/br> Updating br> Over the past week, the adhesive has started to come off in some places due to the rainy weather, but the screws have kept it intact. Using their screws plus adding your own with washers and using rustoleum to prevent rust on the screws is the best way to prevent rust. The rating has been updated, but I only knocked it down 1 star for the simple reason that you cannot expect simple adhesive to hold an object to the bottom of your car throughout extreme weather I still like how it looks and it can be secured.

Kalel Conley

| Dec 21, 2020

Nevertheless, with as many curves as my bumper has, I used it. The screws are 28 in number. It also looks very cool to have a Samurai sticker. You should definitely check this out!.

Cassius Rojas

| Sep 28, 2020

I decided to take a chance and buy this. I wasn't expecting much from it. After viewing the reviews, I'm glad I read them, because the adhesive is definitely not enough to hold it up by itself. Take a little time to go to your local hardware store and buy about 15 more self-tapping screws and washers for about $3. Don't forget to clean the underside of your bumper very well before you attach it. You can cut it with ease because it is pliable and easy to handle. To let it settle flat (it comes rolled up in the mail), I let it sit in my garage for a couple of days. I didn't even need to lift my car or put it on ramps to install this power steering pump. All you have to do is begin at one end, stick it on, and go Using a stubby Phillips screwdriver, I put in 15 screws with washers and I was surprised at how well they worked. It looks really awesome, it is a nice blend of aggression and subtlety to make the front end more exciting. Honestly, it is way cooler than I expected. Some of my friends have already asked where I got it! It has only been on for a couple days, but therefore far there is no wear and tear, and it has not fallen off. Using 110 as a reference point, I pulled over to make sure it wouldn't fly off, and once again, it showed I gave it 4 out of 5 stars because the adhesive alone is definitely not enough, and it probably ought to ship with 15-mil tape as well The screws are 20 in number. I didn't have anything else to say. Thick and high-quality vinyl makes the product very appealing. I've never installed anything on a car that was so easy as this faux carbon fiber. It looks great for the price. Adding something like this to your ride will make it look pretty good for less money and is easy. Be aware that this will not provide downforce, as it is purely for aesthetic purposes.

Adriel Galloway

| Nov 19, 2020