Uni Filter UP-107 1" Clamp-On Breather
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
The height is 2 inches and the width is The diameter of the wheel is 30"
Where you place it will determine how big the impact will be. Most likely, it is on a block vent. I don't think any of the intake vents will work. Before putting it on any pipe, make sure you measure it
No time frame should be set for a replacement. Compared to engine air filters, the amount of air filtered by a cabin air filter is significantly less. Then all you have to do is blow it out with a compressor if it looks dirty.
Selected User Reviews For Uni Filter UP-107 1" Clamp-On Breather
product, I have used it to replace the foam filter inside the secondary air injection pump on my 2009, 2013, and 2014 models You can find more information about this search at A web site called Uni- mod" is the title of the mod. prevent the stock foam filter from degrading which eventually leads to failure of the secondary air pump, causing the truck to go into limp mode, causing the Check Engine light to illuminate, and trouble codes P2440 and P2442 to appear. 13 dollars for preventative maintenance is a good deal. An 05 or 06 will do With the 15 Tacoma, the 2 is available as well. 4 cylinder engine with a 7L capacity or a 12 cylinder engine With the 15 Tacoma, you will have four tires. If you have a 0L motor, I recommend buying one of these filters and switching it out before you encounter problems with your secondary air pump.
For my Lexus GX460, I installed this filter in the secondary air pump. It is expected that the OEM stock foam filter will degrade over time, crumble into pieces, I was surprised to see that the foam filter had already disappeared when I opened up the pump. After further investigation, it was found that the foam filter had already been sucked into the pump, but got stuck inside another pipe. After retrieving the foam filter, I could already feel some of it crumbling to pieces as I held it. The filter fits over the opening of the cover and provides a good level of protection.
The service is not only convenient, but provides peace of mind as well. The 2nd Gen 4 Cyl 2 I just purchased is my first 4 Cyl 2 since the 1970's. There was an emissions system part number 7 and the seller said that this was its part. Anyway, this is all for now. The price of $15 bucks, 1 day delivery, and 10 minutes installation (5 of those minutes were spent cleaning out the old filter) for a little peace of mind is good. In addition, it does add a little bit of retro flair to the engine bay.
Installed this product in place of existing muzzle after removing existing crappy foam filter in secondary air injection system. Found this product in Lexus forums to solve issue with existing foam material getting sucked into secondary air injection system causing pump failure. In order to improve filtration, I recommend adding oil to the filter media, as it does not come with oil. Aside from that, product fit like a glove, and it has the unique ability to work around models that have a design flaw.
After reading a few Toyota Tacoma forums, I discovered that this aftermarket filter will work perfectly with my OEM foam filter. My 2015 Tacoma had 65K on it and it was still in decent In the end, I decided to stay with If the foam did break down, we will be on the safe side by adding 107 to be on the safe side. A quick and simple swap out can be accomplished in just a few minutes. I found numerous positive reviews on the filter and things seem to be going well so far. Due to the type of driving I do, I would expect it to get very dirty. It should be clear how to remove, clean, or replace it when One worm drive hose clamp is all that's needed.
I use this as a replacement foam filter for the air exchange emissions pump on my 2014 Toyota Tacoma TRD Sport. As a result of the OEM filter breaking up, it gets pulled into the pump and clogs it. The cost of a new pump is $2,000. I strongly believe that this filter should keep the pump from being damaged since it fits perfectly.
As of now, everything is going well. This was installed as a preventative measure on my 4cyl Tacoma. There have been a number of reports of the Toyota's internal foam filter disintegrating, allowing materials to get sucked into the fan, possibly causing damage to the unit and sensors downstream ($$$$).
It was after watching YouTube videos that I got it, which said if not replaced within 45 days, it would be a problem. By the end of the first 50,000 miles, the OEM sponge will have broken down You will die if you don't stop As for my truck, it has over 50,000 miles on it since I bought it used. The time had come for me to be concerned, because now I am at more than 60,000. It was the hardest part removing the plastic covers over the pump that I got my friend to help me out with! This was a difficult task that required a lot of tugging and prodding Those pesky questions! The process was easy once you were able to free yourself. Funny, the OEm sponge had almost no dirt on it! It cost me some peace of mind, but it was worth it! The H filter looks sharp, pretty good quality. Way better than the cheap little filter that.
Related Products For Uni Filter UP-107 1" Clamp-On Breather
