TAC Side Steps Fit 2005-2021 Toyota Tacoma Double Cab Truck Pickup 4" Oval Bend Texture Black Side Bars Nerf Bars Running Boards Exterior Accessories (2PCS Running Boards)

Surprised at how well they work. This 2015 Tacoma double cab has five doors. The product is of excellent quality It has a textured plastic finish - as if it had been dipped in a plastic solution This is a very tough and aesthetically pleasing body. In the end, I considered using 4" tubes for the truck since I was concerned they might not be as powerful These are not only perfect, but they look really great as well. In a similar fashion, mounting brackets are finished as well. There appear to be no problems with the bolts because they're coated and Despite being well packed, delivery was not damaged. Getting the program up and running was easy. Each bolt measures 12mm in diameter and is of the same size. It will be beneficial for you if you have a good grade 6 The socket on the 6" extension is 12mm in diameter You will need a torque wrench as well. The bolts are to be tightened only to the recommended torque - do not gorilla torque them You should follow the specification and set them to 16-bits The force on the ball is 18 ft/lb. In this case, it is "spark plug torque. ". The holes on the brackets all line up with the threaded receiving holes on the truck, as well as with the threaded holes on the bars themselves - and therefore the installation is very simple. The trick is to install the brackets to the truck first, then all you have to do is touch them up slightly A tight fit. It should be possible for them to move freely around the facility. Then, you need to lay the bar on top of the brackets and bolt the center bracket to the bar. I'm keeping my finger tight again. After that, move the assembly around so that the outer two brackets align with each other and are bolted in up. To tighten the center bracket bolts, torque them until they are spec Double-check that the rod is parallel to the truck and make sure the bolts on the outer brackets are torqued as specified. You should check all bolts one more time with your torque wrench to ensure they are properly torqued. It requires very basic skills to install this device. After taking my time, I completed it in about 45 minutes.

Collin Campbell

| May 11, 2021

They fit perfectly and went on the truck as if they had come with it. The directions will tell you what to do. Unless you have an extension, all you need is a 12mm socket wrench and a screwdriver to remove the plugs. Although it says 16 pounds of torque, it is not really that much so it is not necessary to use All of the bolts were locked in place with blue lock tight. A jumping test I had didn't move me one bit, and I'm 195 pounds. If the directions say not to tighten until all 3 arms are attached to the bar, then do as directed. They might not line up because you have them too tight on the truck or you have them installed on the wrong side (yes, there is a difference). In addition to "F, C, and R", there are "F, C, and R" market brackets. This one is pretty self-explanatory. You will be able to line things up when you take your time. This took me about 30 minutes to complete.

Zev Combs

| Dec 09, 2020

My 2016 Tacoma Double Cab short bed is equipped with these. The parts fit perfectly, and they bolt on easily. It might not be wise for you to work on your own truck for longer than a half hour It was stated in one review (he liked them too) that he had to cut part of the mud flaps off. There is no touching of the nerf bars and Toyota flaps on my truck. Neither modification nor addition of any kind is necessary. I saw this question too, so I will add my two cents. On some cheap NERF bars, the ends are hollow with a big cap made of plastic. There is nothing to complain about here. A bonus is a They have plastic steps under each door that are placed right at the right place The plastic appears durable, but we'll have to wait to see how the material holds up over time. As this set is not super-heavy gauge steel, I would expect that there are heaver gauge steel nerf bars out there When the weight is heavy, I would prefer less weight to more, and when four-wheel drive is used Rather than pulling the truck body into the nerf bar when wheeling, I'd rather have the nerf bar give and dent. Here is one more hint The rear and front of the vehicles look identical when they are out of the box, but there is a bar attached to the driver's and passenger's sides. You should first look at the holes to make sure they line up with the brackets, even if you are convinced they are identical. You have the wrong side of the coin the passenger side thread The bolt could not be tightened completely without spinning in place, but I couldn't tighten it all the way. Email is my preferred method of communication Following a few images, I emailed the vendor and they sent me a new ticket without me having to go through the hassle of returning the old ticket. OUTSTANDING customer service! My laptop didn't come with a lock - but I found it online! It won't be necessary to use lock washers since the bolt heads are notched (therefore, you don't really need one), but some Lock Tight wouldn't hurt. If you have any stuff like this, I think it's a good idea to lock it tightly. However, the nerf bars look awesome. I wouldn't want to trade them for a pair that's 3 times as expensive. The price is crazy low, but the quality is.

Brooke Bates

| Feb 18, 2021

The price you paid for the service was not too bad. The fit and finish of my 2016 Tacoma is excellent. They still received a 2014 manual with my order, and I would give them a five-star rating. My first thought was that this was probably an error from the The first thing I did was try them on to see if they would work for myself, and turn out that they do, otherwise I definitely would have As a whole, the installation was straightforward. All I had to do was spend 30 minutes doing it myself. There were no issues with the parts. The package came in two days earlier and was in great shape.

Charleigh Albert

| Oct 05, 2020

This set of running boards is perfect for the single cab Toyota Tacoma. You might be able to use them on other models, but I recommend you double check with the manufacturer. These work great with the new 2019 double cab! They are not much smaller than the 2019 models, but they fit the 2017 and 2018 models just as well! Packaged very well, they came in a timely manner. In terms of installation, they seemed relatively straightforward. I think the cartoon would take about 15 minutes in You will need an extension when tightening down the bolts, so you will need a torque wrench and a torque wrench extension. There will be some people who suggest you not use an extension on a torque wrench, but you do not really have a choice. It didn't really make a difference to me I just used a small extension and torqued the bolts down to specs and they worked just fine. Having a weight in excess of 250 pounds really does me in. However, it's just a bunch of French fries and muscle. After standing in them to test their strength, I found them to be strong This is a very sturdy product as it does not move at all. Here's a look at how it looks- They have once again proven themselves to be I love the way they look The running boards are just the right size for my truck they are not to big and not too small, which looks weird but still makes the truck look good. I also find that they provide some protection if someone opens your door next to you, the door will hit the driving As for me, I would rather replace the running board than deal with a dented or scuffed door, so these are perfect for me.

Zariah Charles

| May 08, 2021