Mavic Mini 2 Water Landing Leg, Waterproof Landing Gear Training Kit Extenders Floating Holder for DJI Mini 2/Mavic Mini
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
That's not what I meant. There is ONLY one version of this accessory for mini1 and mini2
From what I can gather, the Mavic air, air2 &amp air3 are a good choice All the Mavic Pro and Pro Platinum have the same diameter around the body, so I would guess they would all fit. I base this only on the fact that I have purchased accessories for the Air that fit my Mavic Pro Platinum just fine.
This skid measures 3/4" from the bottom of the skid to the contact point with
10g is the weight of the DJI mini 2/dji mavic mini landing gear
Selected User Reviews For Mavic Mini 2 Water Landing Leg, Waterproof Landing Gear Training Kit Extenders Floating Holder for DJI Mini 2/Mavic Mini
For those who do not feel comfortable hand launch/landing, these legs provide a nice extension to lift your mini out of the dirt. In comparison, you can quickly snap into place these folding legs, which feel solid and easy to use. I like most is the ability to fold these legs into the Fly More Case so they can be stored under my controller when not in use. Open the legs by bending the tab that keeps them in place, but be careful not to bend the small tab.
It will keep it off the ground on uneven surfaces, and it will save you from getting hurt. The folding design and durability are good, but I can see how it might break in cool weather. You can fold up the props for storage, but then you can't strap them I am a satisfied customer, and I would recommend this purchase to others.
Unlike the prop guards, it doesn't go into payload mode when you're flying. I took it up and flew it around, and it flew like a dream. As well as looking great, they are super fun! It might be nice to paint them a similar color blue to make them match my theme. I'd absolutely recommend them.
My drone accidentally jumped into the lake while I was at the lake last week. Even though it landed upside down (because I had run it into the boat first), the boat didn't sink because I had these floating devices on. By using this device, I was able to retrieve my drone and send it in to be replaced (I used DJI care refresh), and the swim session for my drone only cost $50, rather than having to purchase a new one if it had gone under. For pilots flying over water, this set of landing gear is highly recommended. There is some effect of the floaties on flight if the speed is relatively high (probably 15mph or more). I only gave 4 stars instead of 5. A gust will cause the drone to wobble greatly in flight when these obstacles are present. In spite of this, I won't mind the occasional wobble if it means my drone won't get wet.
My goal was to ensure I have extra ground clearance for landings in remote areas without an obvious take off spot, so that I could protect my props when I land. With this, I can snap it on and off in a matter of seconds, and stow it away in my travel bag without taking up much space. main concern was to make sure I didn't need to register for something because I was still underweight. With all the new regulations, I should still be able to use this in addition to a night strobe and be underweight.
This was part of our drone when in the lake, thinking it might get wet, messed up and ruined if it crashed. We could at least find It probably crashed (murphy's law), and then the red pool noodles were shot out of its We watched as our drone and its landing gear sank to the bottom of the lake in contrast to them bobbing at the top as they should. Despite all of that, we got a couple of free pool noodle chunks as a result, right? This doesn't please me in the least.
On the Mini 2, this landing gear is definitely better than the previous one. By lifting the drone a few centimeters (about an inch) above the ground, it is able to see further. I would use this for landing and taking off on grass or rough surfaces. I flew the drone indoors and did not receive a There were no issues with taking off, landing, and staying in position for the drone.
Unfortunately, the quality isn't up to par. It seems as though the molds created for this project were done very rapidly because they are pretty crudely milled with a number of poorly formed It seems the plastic itself is extremely brittle, so I expect it to crack after a few installations and removals or when it lands hard. I don't have many complaints so far because it works well and fits perfect, so I have no cause to complain.