Traxxas 3741X Red-Anodized Aluminum Turnbuckle Set

$ 22.00

Score By Feature

Based on 288 ratings

Value for money

7.46

Durability

6.71

OveReview Final Score

How Our Score Is Calculated

Product Description

Red-anodized aluminum turnbuckles

2 front camber links (39mm) and 2 rear camber links (49mm) are included.

Traxxas aluminum turnbuckles make it simple to give Traxxas models more strength and adjustability.

Increased bending stiffness is achieved with high-grade 7075-T6 aluminum.

Rod ends are included in the assembly process.

To make the most of your Traxxas RTR vehicles, use Traxxas stock and hop-up replacement parts.

This item is constructed with high-quality materials and is built to last.

This is for use on RC vehicles such as the Traxxas Rustler and Stampede; for exact part listings, consult your user's manual.

Questions & Answers

Is this compatible with the Traxxas Stampede 2WD?

Yes, these are the 2wd stampede's front and back camber links.

Is it possible to fit it on a 4x4 Slash?

This will only fit a 2WD slash.

Is this compatible with the Traxxas Rustler 4WD?

NO, Traxxas 6742 was used in the Traxxas Rustler 4x4.

Selected User Reviews For Traxxas 3741X Red-Anodized Aluminum Turnbuckle Set

After installation, it fell apart twice

3/5

I'm not sure why they fell apart twice, but I suspect it was due to a manufacturing flaw.

Jefferson Leach

| Jul 09, 2021

Broken! In minutes, I was broke!

3/5

Dayton Holden

| May 17, 2021

It's not aluminum like it says! I bought these for my now brushless Stampede three weeks ago, and they seemed to be of good quality and lasted several test runs, but today after work, I took my Stampede out on the road near my house (which is blacktop and flat), and all of a sudden my right back tire was flat on the ground

3/5

My new red aluminum camber link, which I purchased three weeks ago, was completely broken in half. Without a doubt, the quality is poor. These would not break under this amount of pressure if they were made of aluminum, as advertised. I'd expect them to bend before snapping. I'd like a replacement or a refund for these.

Diego Schultz

| May 30, 2021

So far, I'm liking it

5/5

They're the ideal fit! Please take notice! These are for the front and rear cambers, respectively. I'm not sure what setup other users are using to complain about them being too short, but they fit perfectly on the front and rear of my stampede 2wd! br>br>Installed them exactly as they came, and all four tires had about the same amount of camber. To get the camber alignment of the tire at 90 degrees, I adjusted 1 to 1 1/2 turns on each side. Down to the earth. Because there was so little alignment required, almost all of the thread remained inside the heim joint, adding strength. br>br>These camber links look great and are simple to install if you follow the instructions carefully. The steering rods, which are similar to these, will be the next part. I'll update once I've had a chance to put my car through a few packs.

Willa Rowe

| Nov 28, 2021

Great ! Solid, and it helps to keep my rc balanced while bashing at high speeds

5/5

racing.

Julia Stein

| Nov 25, 2021

Turnbuckles for castors

3/5

I have a traxxas stampede 2wd, and the shorter turnbuckles work fine, but the longer ones I had screwed each side out to match the originals' length. The problem is that in order to get to that length, the plastic ends were barely catching any threads, so after a few minutes, one of them pulled right out, forcing me to go back to the originals, which is a shame because they looked great and I really liked them.