DEWALT 10-Inch Table Saw, 32-1/2-Inch Rip Capacity (DWE7491RS)

I have a 12-inch radial arm saw that I've used to build walls with. bookshelves mounted on the wall, workbenches, storage cabinets, picture frames, and a variety of speaker cabinets I now use a power miter saw for all of my crosscuts, and I'm past the point where I'm comfortable ripping large amounts of raw lumber with the radial arm. br>br>Recently, I had to rebuild a rotted back porch on a rental property, which necessitated ripping a large amount of wet, treated lumber for spindles along the bottom half of the porch, as well as numerous other pieces. After looking at every saw carried by our local big box orange and big box blue stores, as well as watching dozens of YouTube video reviews, I decided on the DWE7491RS for my porch construction and, hopefully, some future cabinet-building. constructing projects br>br>Other reviewers have covered almost all of the advantages. I'll focus on the pros and cons of this saw model, so I'll just make some observations based on the sample I received. Of course, there's the table first and foremost. Yes, it is slightly warped, but not to the point of being dangerous. Between the miter gauge slots, it's perfectly flat, but there's a slight incline from the fence. To the right edge of the table, there is a side slot. It sags by about a quarter of an inch. 018" on the right-hand side- back corner, and approximately 0. "012" on the right-hand side- corner in the front I also wish the table had a smoother, more durable finish than the gray painted finish. I tried waxing it before each use, which helped the wood glide more easily, but the gray finish is already wearing off in spots after just this one project. br>br>Most of the saw's adjustments were close to perfect right out of the box. Toes up The riving knife alignment and runout were both spot on. The blade, on the other hand, was a zero. When set to zero, the angle was 40 degrees past vertical, and at 45 degrees, it was slightly off. The fence was a few thousandths out of square, and the rip scale was slightly off as well, but both were easily adjusted. br>br>The cam discs used to set the 0° and 45° bevel stops on this saw aren't my favorite. It necessitates far too much testing. When the Allen bolt is tightened down, the cam wants to rotate slightly, so it takes some trial and error to get it perfect. The machine screw is much more appealing to me. On most of my other power tools, I use a locknut system for the limit stops. br>br>Overall, this saw is a beast, and it ripped some extremely wet, treated 2x6s with ease. I did trip the breaker a couple of times (at the load center, not the saw), but once I moved the shop vac to a different branch circuit, the problem was solved. Because of the electronic start, you can't control both the saw and the grinder with a single switch. This wasn't a problem because of the vacuum. br>br>At first, I was annoyed that the saw came with two different sizes of dust ports, as well as a user manual recommendation to use a Y-splitter. However, no such adapter was included (nor was one available for purchase at any hardware retailer I could find, including the Dewalt website). Fortunately, with the help of a shop vac and a 2-inch hose, the mess was quickly cleaned up. There's not much sawdust coming out of the 12-inch bottom port. Rather than rigging up a 2-way blade guard, use a 12-inch blade guard port. ½" Y- a hose and an adapter I just transferred the fabric dust bag from my miter saw to the blade guard and it seems to work fine. br>br>Another minor annoyance, which is common to nearly all job site saws, is the inability to micro-adjust the blade guard. The bevel should be adjusted in the same way as the blade height. It's not a big deal for the rough carpentry I'm doing right now, but I'd like to do some finer work in the future, and this feature would be useful. The Ridgid saw attempts to address this issue by incorporating a dual-purpose blade height crank. Spring has arrived. When you load it and press it in, it engages a curved rack. The bevel angle is adjusted with the help of a pinion gear. It's a clever concept, but in practice, I found it to be a little clumsy. (I didn't try the micro-blogging option. ) The SawStop's bevel adjuster was way out of my price range. )br>br>Aside from that, I'm pretty happy. Everything (except my new dado throat plate) fits onboard and is very easy to set up and break down. The anti- Although attaching and removing kickback pawls from the riving knife can be difficult, I've found that they work well. br>br>Other reviewers have expressed dissatisfaction with the miter gauge that comes with this saw, but I didn't find it to be an issue. I'll look for a suitable Incra when I come across a project that requires it. Years ago, I learned this lesson from my other expensive hobby, astronomy. You can spend tens of thousands of dollars on a high-end computer. It will still come with a toy finder scope (a small telescope attached to the main optical tube) at the end of the telescope. Why? Because there are a plethora of after-care options available. There are a variety of market models to choose from, each with its own unique characteristics. Miter gauges are the same way. There's no way a mid-sized company can compete with a large corporation. They don't even try because a reasonably priced table saw can include a gauge with all of the features found in various Incra or Kreg models. Furthermore, a couple of layers of plastic (exterior grade) painter's tape applied to the rail can make the included gauge marginally functional. This eliminates the majority of the slop while still allowing it to slide through the slot smoothly. (A YouTube video demonstrating how to do this is available, but it is fairly self-explanatory. ) self-explanatory )br>br>I'll update this review if something particularly bad (or good) happens to this saw after a long period of use.

Gavin Norton

| Aug 25, 2021

These saws appear to be upgraded versions of the previously successful 744 and 745 series saws, which were introduced in late 2013. A no-load blade speed of 4,800RPM (up from 3,850RPM) and a larger dust port (2-inch) have been added to the previous series' specifications. 1/2" vs. 2-inch 1/4"), a slightly heavier weight, and a new rolling stand system with integrated tool for the 7491. Storage for safety equipment. The 7490X and 7491RS series, in particular, have an improved fence system that has pushed the industry limits of contractor saws past the 24-inch mark. Barrier is 1/2 inch thick. Apart from the aforementioned upgrades, the majority of the other specifications (such as cut depths) are the same as the previous 744/745 series. The 7480, which was previously crippled, is now unaffected. Even the cheapest model comes with a 24-hour warranty. Cut sheet goods in half with a 1/2" fence. Dado blades can be used with both the 7490X and 7491RS, but Dewalt now recommends against using them with the 7480. " At the moment, the new series appears to have a higher price tag, but the money appears to be well spent. The tried and true rack The pinion fence adjustment is still available, ensuring that your fence remains true even after a lot of use. br>br>The new models appear to be similar to the previous series in terms of differentiation, and the deciding factors are fairly straightforward based on your requirements. If you're looking for a straightforward 24-hour service, this is the place to go. If you need a 1/2 rip capacity saw without a stand, the 7480 is the way to go; if you need a 28-rip capacity saw, the 7480 is the way to go. The 7490X is your best bet if you want maximum portability in a rolling stand with an impressive 32-inch display and a stationary (but still portable) integrated stand. The 7491RS series offers a 1/2" rip capacity as well as fully integrated system storage. br>br>Some people believe that 24-hours is a long time. It only requires a 1/2" rip capacity. True, you can rip the short side of a 48" sheet well, but you'll end up with a lot of material hanging off the blade's left side. It's a given that you can't do it alone, and the improved fence system addresses this issue by providing adequate material support where it's required. It has two fence positions, one of which can be moved outward to accommodate the large 32-inch screen. The capacity is 1/2". The measurement scale accommodates both fence positions, with one beginning at 0" and the other at 8", and it was fairly accurate right out of the box. (For more information, see the following usage update. ) ) I've noticed that the fence material support bracket is less strong at the maximum distance, but it doesn't appear to make a significant difference since it's really only for basic material support. br>br>I've never used the previous model of rolling stand (744 series), but based on what I've seen on YouTube videos, I believe this one is a bit easier to manipulate. Despite the fact that the saw and stand are fairly heavy when assembled, moving it from storage to operating position (and back) is a safe, simple, and quick process. It may be difficult for people who are shorter or lighter, but it is simple for me because I am of average height and weight. The saw is as solid as a rock once it's in place. There are no movement issues, and it isn't particularly side heavy in any direction. The fact that the handle can be positioned in two different ways was also appealing to me. easy-to-use and compact (for more compact storage). carry. br>br>Assembly was very simple, and the instructions/diagrams are very clear; it took me about an hour to put it together and another hour to learn how to make the major adjustments and perform blade checks so I could get started. All of your common adjustments are easily accessible, and I discovered that the calibration adjustments I needed to make were simple to complete. It's great to have all of your safety equipment integrated into the stand; everything has a place, and it's less likely that safety equipment will be misplaced or go unused. A no-fail recessed power supply is standard on the saw. In an emergency, the on button has a large stop that can be easily kneed or kicked. Although it's unlikely that this device will turn on by accident, it's always a good idea to be cautious. When working with the blade directly, turn off the safety switch. Because the riving knife accessories are so simple to install and remove, I'm sure I'll use them most of the time! br>br>At the moment, the lack of accessories is one of my biggest complaints. I heard that the older series dado inserts aren not a 100% match and fit quite loosely in these new saws. Dewalt does not currently list any accessories for this particular saw on their website. As a result, that's probably not the best option right now. (Note: A dado plate, part DWE7402DI, has been available since late 2014. However, unlike the 7xx series, there are no infeed or side supports. ) In the meantime, you can use a generic adjustable roller stand (or a custom built outfeed table) and DIY dado/zero clearance plates; I considered docking a star for this, but I don't think it's a big deal right now because there are workable solutions. Also, the miter gauge that comes with the kit isn't very useful, but anyone who's semi-experienced with woodworking will find it useful. Anyone who is serious about outfitting their saw will build or buy a decent crosscut sled and a miter sled. br>br>Overall, this machine is approaching cabinet saw capabilities thanks to its increased power and larger fence system. It's not a perfect replacement, but it's a lot better than the predecessors' and competitors' offerings. If you're anything like me, you want the capacity of a cabinet saw but the need for storage and portability takes precedence. Then you should definitely take a look at this unit. Yes, it is currently the most expensive of the common portable contractor saws on the market, but if the increased fence capacity and refined portability are important to you, it is money well spent. As the saying goes. Once you've made a purchase, you've made a cry. br>br>I'll update this review once I've had a chance to put it through its paces with various materials, but it's already performing admirably. I had no problems with either of the soft woods (pine and fir), and I could tell the hard woods (walnut and cherry) had more power. So far, it's been a QS oak. I got nice, clean cuts, and my quick fence measurements were accurate enough for me. The provided blade is adequate for rough cuts, as it is with almost any saw. Any fine work, however, will require 60/80 tooth 10" blades. I'll be putting this saw through its paces over the next few weeks, as I have a couple cabinets to mill down and build. br>br>Update on usage: I've now spent several hours with the saw and have a good understanding of its flaws and limitations. br>br>* It slashes through everything I've thrown at it with ease. I found some 8/4 cherry to try, and while it slowed her down a little more than I'd expected, she chewed right through it, and I believe it could easily take on a 12/4 piece with enough time and patience. I'm also a big fan of that big fence, and I've been using it a lot more than I expected. It's been fantastic to be able to quickly and easily cut larger panels. I can only cut 4'x4' panels comfortably on my own, but I was able to cut a 6'x4' panel in two cuts without too much difficulty. (One is a rough draft, and the other is the finished product. ) ) Anything larger (particularly full sheet cross cuts) will necessitate assistance or the use of a good infeed/outfeed system. Be aware that if you use this saw hard enough, it will draw more than 15 amps, tripping fuses/breakers rated at that level or less. When I push hard on a vacuum switch with a 15 amp fuse, it trips. My breaker would most likely blow if I didn't have that. br>br>* In my original review, I stated that the table top was "as flat as could be. " "Well, according to my dial gauge and straight edge, there's about a slope of. The width of the table is 015". As far as I can tell, this has no significant consequences as long as your blade is at 90 degrees (or the desired bevel setting) to the slope. In addition, the tabletop and coating are not to my liking. When I was building my panel and cross cut sleds, I discovered that even the tiniest amount of friction was enough to rub it off. (Getting the "used" look didn't take long at all. ) ) It's also non-ferrous, so no magnets are allowed to be attached. Because actual metal is, umm, heavy, it's most likely to save weight. If necessary, clamps, both regular and miter slot, will be used to secure the pieces. br>br>* Upon completion of a full tune-up Checking my up/settings, I discovered that my fence distance gauge was off by over. 015". It wasn't a big deal, and it was a simple fix, but I was having trouble cutting off the gauge with even close to precision. In addition, my fence at position 2 was nearly parallel to the miter slot. Front-to-back measurement of 010" It's probably not enough to cause issues with most cuts or rough work, but it's excessive for my tastes. It was also a simple fix, but getting it "just right" took some fiddling. " It was a little annoying to have to tweak a new saw into perfection, but it wasn't too difficult, and this is probably due to the saw's primary market being rough work, not cabinet grade. If you want to be precise, you may need to make adjustments at the factory. A good try or combo square, a shop-made fence measuring jig (or an A-frame fence), and an A-frame fence measuring jig (or an A-frame fence measuring jig) are all things I recommend. For measuring error rates, use the Line It jig and a digital or analog caliper. br>br>* I discovered that removing the blade from my 60 tooth fine blades necessitates removing the dust shroud. It's an inconvenient step that takes about a minute longer, but it's not a big deal unless you're constantly changing blades. br>br>* Until Dewalt does something, total dust collection will remain a mystery. At the very least, if you use a Shop Vac and 2-in-1 cleaning solution. Hose is 1/2" in diameter. The 2- The 1/2" port is solid and catches the majority of dust, but it does kick up a fair amount of dust. As a result, they created a riving knife with an integrated dust chute. This is a fantastic option, but it's far too expensive to pursue right now, rendering the accessory nearly useless. There is no such thing as a 2-. 1/2"x1- I'm not going to use 5 fittings, convert to 4", and add a bunch of extra hose to do it because there's a 1/4" Y adapter out there. I prefer the normal fallout from using a regular knife to shooting it six feet across the room. br>br>* Here are a few quick facts about this saw that are difficult to come by. It can fit an 8" dado blade with a width of up to 13/16". (I didn't use a 6" dado this time, but an 8" worked just fine. ) I can see how a 6" would work with a shallower maximum depth. ) The height of the working table is 36 inches. 3/8". The maximum storage height is approximately 44 inches. 3/4" when the handle is in the compact position, or just over 48" when the handle is in the easy-to-reach position. position to be carried There is a great deal of erroneous information on the internet. information found in the Q These measurements come from my actual 7491RS saw, as well as from the manufacturer. If you require any additional measurements, please leave a comment. Other than that, I still think it's an excellent saw. br>br>Accessories for this saw will begin rolling out in Q1 of 2014, with a dado plate being the first expected accessory from Dewalt. br>br>Aside from that, I still think it's an excellent saw. Maybe 4. Due to the from-, I'd give it a five-star rating. the- My disappointment with the table top, as well as the factory adjustments I had to make. Aside from that, it's been easy to use and work with, and it's producing excellent results and perfect joints for me. If anything new comes up, I'll let you know.

Sutton Ibarra

| Aug 03, 2021