WEN 6515 1 in. x 30 in. Belt Sander with 5 in. Sanding Disc
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
There is no need for the hook and loop play on disc sanders since most of them are glued on. The answer to that question probably depends on how you intend to use it.
Yes, it can be, but you will most likely need to attach it to a board first, then screw the board to the rails. Indirect access is difficult since the bolt holes are located so that they are hard to access directly.
Quick shipping is available when you order from Amazon.
I believe it would handle it fine. It actually has good power and will not delay if you need to push hard against You just need the right grit to remove the material at the right rate. It is being used for refinishing steel components with 220 and 600 grit
Selected User Reviews For WEN 6515 1 in. x 30 in. Belt Sander with 5 in. Sanding Disc
They are easy to find, change, This is a great It is easy to switch belts and track the belts to center from the belt section. This belt has a metal plate which makes it easy to sharpen handheld tools such as chisels, knives, scissors, and other hand tools. My experience with the motor so far has been favorable, and it does not seem to bog down under heavy The motor did not have any issues whatsoever during the 3 hours I worked with it right out of the box. I often drop tools if I rest them on the belt deck, because it is hard to keep the belt tight. no longer use the deck to sharpen my tools, and just sharpen them on my own- In hand. The disc is a piece of As the pad is attached to the machine by glue, I had to use a heat gun to pull it off, and then clean the remnants of adhesive A hook and loop pad is now located in the disc section, and you can simply buy the paper for them. The problem has been There is more strength to the disc's deck than to the belt's, but it is still quite thin. It is not possible to accurately measure the angles on the decks. To date, I have not faced any walking or balance issues, nor have I experienced any wobbling. Over the past three weeks, I have worked about 20 hours on this machine, and I am already planning on buying another one for my brother for Christmas.
At first, it appeared it did what it was intended to do, so I purchased it to teach a knife class to young men. This is a problem with the belt speed, which is too high and appears to be regulated, so it is not possible to lower There were 12 boys that completed the class, but the sander is becoming increasingly louder and louder as time passes. There seems to be a problem with the balance of the wheels. At this point, I'm not sure what can be done. There does not seem to be any difference among the types of sand paper I've used.
While I wanted to enjoy this unit, installing the belt table was impossible and I didn't like it. It is impossible to get any help from the minimal instructions. If I were to try to explain it, it would be too complicated and time-consuming The table is supposed to be secured with a lock lever, which in its current form cannot be installed because the handle of the lock lever is fused to the bolt at its end. This means you can't rotate it to seat it correctly in the captive nut under the Having no other option, I guess I need to find a straight bolt that fits You can loosen and tighten the bolts with a wrench Ensure that the table is tightly seated. It is not worth the effort, and it is definitely a loser While I would return it, it will be more trouble than it is Other Wen items I have purchased have been satisfactory, but this one has made me hesitant to ever purchase any more from them. A RECENT UPDATE You must first take apart the locking lever. Remove the allen bolt (with spring) from the end of the lever, ensuring to catch the spring when you do. The mounting bolt should be in one hand and the wrench in the other The lever on the other wiggled a little bit Pull the bolt out of the table, then install the washer (don't forget it). To tighten, tighten the finger firmly After the lever has been fully lowered, attach it again in Replacing the allen bolt and allen key is the final step The spring season. A lever at the top of the table can now be pulled up to tighten it.
This is my first product from them. Since the price is so low, I was slightly hesitant to purchase it because I assumed I would not get what I paid for. I was wrong in my assumptions. My use of this extends over two days, each day for a few hours. We have not had to adjust the belts and they are still in good condition. Even though I do not believe all the instructions were correct, if you use your head, logic, and common sense you can get the installation to work. The sander has a powerful motor and is well made. As for the H, I have also borrowed it from my dad. This is the best version of this sander, and I In comparison to the WEN, the quality was comparable, but the price was more affordable and it was easier to set up. With the WEN belt sander you will not be disappointed.
I was missing three screws that were required for mounting the orange air duct to the metal chassis of my sander. It appears that other buyers have experienced the same problem and complained in other reviews as well. Due to the good value of the sander, I got three screws to replace the ones that came with it, which was faster than returning the whole unit. For this reason, if you wish to keep the sander, you should purchase There are a total of 10 metric size 4 screws in this package. I think slight variations in M4 length could also work, from the looks of things. They can be purchased on Amazon (usually in kits of different sizes) or at your local Below you will see the attached picture showing where I used these three screws to mount the air duct to the chassis. I wish you the best of Do refer to the attached picture if you have any questions about the instructions.
As far as I can tell, the plastic tracking knob was adjusted to the right by using pliers to adjust the tracking knob. There are also some decent dents and scratches on the unit. It looks as though the tracking was damaged when this one was dropped. In spite of the fact that the belt hangs off to the left, the tracking has been forced to the right. Sadly, this is no longer usable for me in its current As soon as I am able to get a replacement that's in good working order, I'll update the rating.
The sander I received after returning the first one wasn't very good. I received the first one with bad rollers that interfered with the alignment of the belt. Also, the table was very rough and had a lot There was roughness and chipping on the housing for the disc sander. Despite the two sanders I received, I am quite satisfied with both of them.