Carving Expert 100pcs Multifunctional Wool Felt Mandrel Mounted Grinding Polishing Accessories Attachment Set - Fit Dremel-1/8 Inch Shank
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
I'm really impressed with how long these last; I used to polish watches, and these have withstood the test of time. Because they don't shred, I can use them multiple times. Firm, not soft, is how I would describe it.
As far as I'm aware, there are no grit options. All of the items are made of tightly woven cloth that is only used for polishing.
Sure, as long as you don't go too fast near any plastic components. It was purchased for the purpose of polishing hard-to-reach areas.
No, it will not withstand the test of time. It's made of plastic, and mine was broken when it arrived. The cover was cracked and broken, and it couldn't be closed; it just sat there, falling off every time. It's ugly and it doesn't work.
Selected User Reviews For Carving Expert 100pcs Multifunctional Wool Felt Mandrel Mounted Grinding Polishing Accessories Attachment Set - Fit Dremel-1/8 Inch Shank
This is the fourth time I've decided to buy something. It was the first time in 2017. They last a long time; however, when working with metal, polishing should always be the last step (which most people assume is self-evident, but even professionals don't fully comprehend), and it should not take long. That means if you're using a felt polisher a lot, you should take a step back and use a 1000 - 2000. Sandpaper with a grit of 3000. With metal, super fine grit sandpaper is used for the majority of the hard work. It is much more straightforward to obtain a genuine-to-life experience. Surface that is flat and even. Unfortunately, this means that you'll have to put in some elbow grease and sweat equity to complete the project. THIS IS VERY IMPORTANT! IMPORTANT NOTE: It's not the same as drilling when it comes to polishing. The larger the drill bit, the slower the RPM; as a general rule of thumb (with a drill), the larger the bit, the slower the RPM; Similarly, the RPM increases as the bit size decreases. While felt polishing tools may resemble drill bits in appearance and function, they are not the same. They do not fit into this general rule of thumb classification because they rotate around a central axis. Use the slowest RPM possible when using a felt polishing tip, particularly the smaller ones. Many Dremel tools allow you to choose between 5,000 and 10,000 RPM. 8000 RPM. With the small tips, this is the fastest speed I would use. Another user's pictures demonstrate what happens when the RPMs are increased - The tip IS GOING TO FLY. Keep in mind that polishing is the final step in the procedure - It has to be handled carefully. So, any manly, beefcake welding/pipefitters out there who think they can slam bam their way through fine detail polishing, thank you. you- The attitude of ma'am will only disappoint you, and you will most likely leave negative feedback.
These felt pads were purchased to polish a couple of Glocks, and they did a decent job. I used two pads per gun, one for the upper and one for the lower parts, and they quickly turned black, but flitz polished everything to a mirror finish. I haven't used them for anything else, but for the price, I'm very pleased; the case is also nice and keeps them sealed while allowing you to stack items on top of them.
There are some negative reviews for the "100pcs Multifunctional Wool Felt Mandrel Mounted Grinding Polishing Accessories Attachment Set," especially about the smaller diameter tools coming apart, but felt, like any other material, has physical limitations. It's not because they're made of cheap parts or have a bad design that causes them to fall apart. The issue is that most die grinders, such as my variable-speed Dremel tool, aren't designed for this purpose. is that it spins so fast, even at the lowest setting, that centrifugal force literally throws the felt off the bit. CAUTION! IF YOU ARE NOT COMPLETELY QUALIFIED TO DO ELECTRICAL WORK, DO NOT ATTEMPT THIS. My solution was to use a dual gang box with a power cord to house a 110 volt outlet and a dimmer switch, and then wire the outlet to the dimmer. This enables me to slow down the die grinder, extending the life of the felt while also allowing for less vibration and finer, more detailed work. It's also worth noting that this could theoretically damage or destroy your die grinder, and it's not something any manufacturer recommends, and it will certainly void your warranty. If you attempt this, don't over load it and don't try this on larger 1/4 inch die grinders such as a rotozip or a dewalt, you will fry the dimmer and You do so at your own risk if you try this. Do not leave the grinder unattended while it is plugged in; insufficient amplitude can result in overheating and a fire hazard.
They were exactly as they appeared in the photos and were of excellent quality. The tip appears to have a long life, but for polishing work, I set the speed of my dremel to 5,000 rpm. Buffs aren't consumed as quickly as other animals. I'll say that these seemed a little more difficult than the ones I usually use. They're ideal for pre- and post-production. polishing, as well as the initial polishing However, I do not use them for the final polishing of sterling silver. That's fine; I'd still purchase these.
These are excellent polishing bits that fit perfectly in my Dremmel and Black and Decker tools, are well-made, and stand up to the polishing abuse I subject them to. All of my jewelry and fingernails are held in place by them. In fact, I just used one bit to polish my mailbox, and it's still working fine. I like the variety of sizes as well as the fact that the polishing cloth heads are included. I also like the neat case they come in, which keeps me organized and ready to go at a moments notice; overall, I'm very happy with these and will be back for more when they wear out.
Purchase is not recommended. I purchased this in the hopes that it was made of cotton rather than wool. I'm not sure what it's made of, but it didn't last more than 2 minutes on my rotary tool at 12000 rpm (the tool's lowest setting is 10000 rpm). br>br>See photo.
These are ideal for use with a Dremel. Using Flitz and Mother's polish, I used them to polish metal objects. Since undergoing this treatment, the "actions" have become much more fluid. And because these items were inexpensive, it didn't hurt my wallet to do so. I'm hoping to find a way to recycle them.
These are excellent value for the money. They're being used to polish the crevices of aluminum engine parts like intake manifolds. They don't last long and begin to stink after being overheated. However, given the roughness of the surfaces I'm polishing, the aggressive compound I'm using, and how hard I'm polishing them, they're lasting longer than I anticipated. While polishing the intake manifold, I believe I used up about 6 of them. This is a fantastic deal because you get so many of them.