Replacement Trigger Valve Kit fit Bostitch TVA6 TVA11 Repair Parts
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
This is something that I think
Apparently, this TVA6 will fit yours. If this TVA6 (replaces TVA6-- The trigger needs to be easily repaired and can be done for a reasonable price for the trigger if 1) holds true. The valve itself will not work, so do not try to fix it.
The TVA6 for model 0 is In the two-sixths of an inch
The nailer worked with it perfectly. There is a model number, but I don't know it.
Selected User Reviews For Replacement Trigger Valve Kit fit Bostitch TVA6 TVA11 Repair Parts
I had it in ten This solution will definitely fix air leaks out of the trigger if you have them. It requires you to remove it and grease the inner o ring assembly (I used automotive silicon grease that To remove tool roll pins from the valve, you do not get a drive pin tool like you would with a Using an old dill bit (turned over, of course) will work just as well and cost you less than I have been using these since I left this review and they have been great. The nailers work great with these - I've used them on three bostich nailers The finsish, framing nailer, and skylar coil nailer (all of which have been leaking) have not done so but none of them has It's quite inexpensive compared to the Bostich OEM spares, so I keep a couple spares in a drawer.
While working on a project, I noticed that my Bostich pneumatic framer was also malfunctioning. Trying to find a lubricant and adjusting parts was not an option due to time constraints. As soon as that didn't work, I got frustrated with the hassle my tool was causing me and I threw it off the roof (not proud). I replaced this part in less than 10 minutes and the gun is now as good as new despite the damage to both sides There is a fall in the story. The future will be better for my tools if I treat them well.
In my previous job, I was a back-up Carpenter's work in the backyard or on the farm. In the past few years, I have purchased a nail gun to build a board fence and honestly, have not used it often. In the process of re-nailing an old piece of wood, I decided to use a nail gun An air balloon triggered by a roofing job caused a large amount of air to be released. The problem was looking at the two roll pins and I saw that I could punch them out and possibly get the part that was leaking out. tried to fix it myself but was unable to, so I ordered this and it fixed it! Installation is quick and easy. This repair is doable by anyone with a pin punch and a bit of common sense.
They appear to be the same as the OEM triggers I used to replace them. It was easy to install, but there were no instructions, but you put them back in just as you did with the others. As a side note, you need to make sure that the slots line up with your pins before you install them, or else you will not have Take the trigger pin out first, then the body pin, as you remove the old one. Pull out the old pin once the pins have been removed with pliers after you have removed the pins. There are some who recommend applying air if they don't fall out. APPLY AIR ONLY after the pins are in place - DON'T apply AIR without the pins. The importance of this cannot be overstated. Essentially, you will have a projectile at a very high velocity. If you just replace the valves, you will be back on the move in no time at all. Considering the quality of my guns, I cannot comment on the durability. I have only used my guns a few times and just replaced them.
Although it didn't come with lube like the kits do, it was still more economical to buy a small tube of grease for a couple bucks than to purchase To be able to buy one again rather than be shut down, I will purchase another one.
Almost perfect. The fact that I can repair a quality tool for a small amount of time, patience, and money is very gratifying to me. I purchased 2 copies. For peanuts, I fixed 2 Bostich narrow crown staplers that are 15 years old. Mended them to work and they work perfectly.
It was easy to fix a broken finish nailer with this kit, and a broken piece of equipment was quickly restored to service. I would recommend buying two of these kits if you are as infrequent in using your nailer as I am.
I only had to fix my nailer for two minutes This part has been re-inserted with a new set of rings. My hand was all mushy after I pressed it all up, so I had to nip the My nailer is still broken after I spent an hour repairing it.
Related Products For Replacement Trigger Valve Kit fit Bostitch TVA6 TVA11 Repair Parts
