Greenfield Kickstand 285 or 305 mm in Two Colors
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
In order to place an order for the Greenfield Retrokit , you have to purchase the stand without the mount. When you buy the stand, you do not get
There is no way to do that. There is a requirement for ordering a rubber foot
It is almost the same size for 700c and 27 in. It is the length between the chain stay and the bottom bracket that is of concern. In 2014, I had a welded bracket intended for a kick stand like this on my specialized sirrus. Don't ride your carbon fiber bike if it is made from carbon fiber. I would use an old inner tube to protect the paint, moly.
An ordinary hacksaw can easily be used to cut the kickstand down to the correct size. This is accomplished by indentations on the stand at about 1/4" intervals.
Selected User Reviews For Greenfield Kickstand 285 or 305 mm in Two Colors
It is hard to beat the price on this stand. It is durable and solid, but there are a few things you should be aware of before cleaning up after installation. Ghost Kato, a motorcycle with 24 inch wheels, had to have its front end cut off about an inch with a hacksaw. You can make the cut without much difficulty since it's aluminum, but you have to have a hacksaw if you have to adjust it. If the stand touches the ground at a right angle, then you need a large hex key in order to tighten this. * Before you begin cutting, make sure the stand is at the same angle so that it is roughly flat on top. On this bike, the bolt is recessed, so I needed a hex key, not just pliers around the groove. In my usual tool kit, I didn't have a hex key this big but I did have one in my mechanic I'm just letting you know. It's not a big deal. The rod is incredibly secure and sturdy once I tightened it down with the included washer and cut it to length. It's a good purchase, I would buy it again and also recommend everyone else to buy it.
It seems that my six year old and my four year old are both obsessed with kickstands at the moment. The child is five This is the first time they have used The historical revelations were the only way we knew of them. A second hand bike (secondhand) had kickstands. In the car, they asked if their new bike would have them. In response, I said I wasn't sure. As for the kickstands, both bikes did not have them. As soon as I told them I would order them, they thought that nothing could be better than living life to the fullest. It is my son who says that. Is that what I get?" That's right, I get my own kickstand. It is what I have to say. Singing with joy, they said, "Yes, yes, yes, we have our own kickstands. ". The kickstand should be cut at 220 A for Specialized Hotrock 20" and 180 A for Hotrock 16" as not to detract from this review because it is a moment of joy only found in a child's life. " If you decide to use the optional rubber foot, the numbers will be different. I just wanted to point out that the wheel sizes are 20" and 16". It's not clear whether it's the same for different Make sure you measure twice and.
The 20" bike I bought for my kid is very easy to use. Don't forget to measure 5 times and cut only The best thing to do for the start is to take less than more so you can see for yourself if the bike leans well. You can reduce your off-screen length without affecting your gameplay, but if you reduce it more, you can still adjust. I used the hack where I installed both full and minigames. My bike was attached to a kickstand with a hole in the mounting hole, so I held the bike in my garage with the kickstand leaning in the water The edge of my garage is marked by a "step". In the 1 to 1 ratio, 1 is equal I just cut off a 5" section of the garage door to put the water step in. The purpose of the fence is to keep rainwater from backsplashing into your garage when it rains. The difference in height was marked with a sharpie so the threshold was at the same level as my garage,.
I tried a couple other types that can be adjusted higher or lower (which always loosen) and attach farther back (which doesn't hold the bike up nearly as well as this one). It's the perfect old school design. If the back wheel is too long, you can always cut it with a hack saw if it's too long. There was a slight problem with the length, so I quickly adjusted it to fit my kids' bike. Simply hold the bike up on a curb with the kickstand in the "stand" position hanging down the side, tilt the bike to whatever angle you want, then mark the kickstand at the level of the curb. There's no problem cutting it, it literally takes a minute.
I ended up wasting $5 on the difference in price because I had to cut my kickstand down to 285mm. The only good thing about my cuts and work was that I could mount the frame myself. That would have cost another $15-$20 A bike shop is selling bikes for $20 apiece. The pythagorean theorem can aid you in estimating the proper kickstand length. The size of a tire does not dictate the size of the rear axle, chainstay, or kickstand mount.
Due to a defective Greenfield kick stand that was too short for my DIY ebike conversion, I was able to replace it. The kick stand was straight and I didn't have to cut it, it can bear the weight just fine. I bent two other adjustable kick stands made from.
The kickstand is a Greenfield, which is about the best kickstand money can buy. A star has been taken off because the seller could have made it more clear that this kickstand does not come with the top clamp, which means it won't fit on most bikes. You will need a top clamp to attach your kickstand if your bike doesn't have a bracket with a hole for it. Most bikes don't.
Two of these were just installed on a Specialized Hot Rock 16" bicycle for my kids. Vice President of the company got back to me in less than 24 hours after I emailed. Included with the bolt are the lock washer and washer. Near the bottom bracket, the kickstand mounting base fits perfectly into the factory kickstand mounting plate. It is only necessary to trim the kickstand. FYI, If you have the same bicycles, this is how I trimmed the kickstand to align the bicycles with the end of the kickstand.