Calculated Industries 8125 Value Pack - Blind Mark and Center Mark Drywall Install Tools | For Electrical Outlet Box and Recessed Can-Light Cutouts | Powerful Rare-Earth Magnetic Targets and Locator

In a nutshell, Installers of drywall who are neophytes can use this tool. Although I am not a professional, having installed drywall enough times over the years makes me not intimidated by having to cut holes for electrical boxes or can lights during installation. If someone is unfamiliar with the process of cutting holes in drywall and has never measured such holes before, this set of magnetic guides will likely prove invaluable. The guides are placed into the single receptacle/switch box, where they are held in place by clips to the outside of the box, self-leveling The centering of the box should be in the middle. A dry wall is then hung over the box/can and the second magnet is placed on the exterior of the drywall and moved until it locates the magnet in the electrical box on the other side, following the same method of installing the drywall. First of all, drywall is usually hung with the exterior sides of electric boxes flush with it. As a result, in order for the dryall to function properly, it is likely only to be partially screwed down. The screws should not be tightened too much, and the boxes should not be mounted too many screws before the holes have been drilled. The second issue is that there may be approximately one eighth inch of play with Using this system, you will probably get a close fit, but not a perfect fit. It comes as no surprise that when you measure for your hole, some degree of error will also occur. The third point is that they are designed to be paired with It's possible they might help with double, triple, etc. gangs, but I think they're best for single-gang situations. Fourth, check out the video for a glimpse into how well these hold in half as well as a full-sized pool The drywall should be 12 inches thick. As far as I can tell, they're doing pretty However, I have not yet tried them in 5/8 inch drywall.

Randy Good

| Oct 14, 2020

Doing just about every home improvement on my house and doing a lot of woodworking is one of my favorite things to do, but drywall is a problem for me. That's the only thing I don't like to do. That and climbing on the roof, too. Cutting out boxes is one of the most difficult parts of working with drywall. This tool is always welcome, so it deserves your attention. I think it's a fantastic idea really, just pop the part into the box, put the drywall up, and then pop on the other tool piece and make sure everything is level. The actual functionality is quite good. What I like about it is that it works easily and it works well. There is one thing I noticed, you have to take care when putting on the outside tool part, it can easily be turned, or can be turned From the pictures I posted, you can see what I mean. There is no defect in the product, but it is something you need to take into consideration. There could have been an easier way to lock it in. I think this is an excellent plan and recommend it to everyone. Yes, I would really appreciate your help when it comes to cutting.

Nicole Brandt

| Sep 21, 2020

My first job was hanging and finishing drywall for a drywall company, helping me earn money to pay for college. Back then, there was no technology like this. I am very happy to have these "Calculated Industries 8125 Value Pack - Two Bolts" in hand as I prepare to hang drywall in a cabin I am building. A tool for installing blind marks on drywall and center marks on drywall. My plans are to begin hanging drywall in a week, but for now I use a piece of 5/8 inch drywall to get a feel for how well they work as I will need to take out several wall plugs, switch boxes, and recessed lighting panels. It seems logical to me if these center marks work well on 5/8 in. drywall, they should be even more accurate on 1/2" drywall that I will be using I have tested these center marks a number of times and they work beautifully! Taking a look at my test photos, you can see that the center marks line up perfectly even with the thicker 5/8 inch piece of drywall. Based on what has been said before, I have the following pro and con opinions Feature of the wall box center marks• The spring loaded clips is used for holding the wall box marks into the In addition to holding tight, they will not fall out when you put up your There is a strong magnetic field in them. Even though the drywall was thicker than 5/8 inches, they centered perfectly. A light can center mark will be able to be adjusted to adjust for cans varying in depth. When the drywall is thicker than the can, the center of the marks still align with the center of the can perfectly. I am able to hang a full sheet of drywall in all scenarios at my cabin with the box inserts and the can inserts provided with each set. As you can see in the picture, my kitchen ceiling has six cans of recessed lights. Due to the fact that each drywall sheet will have two light cans, the two lighting can tools are perfect for locating the cans. Their ease of use is a plus. The centers of the boxes and light cans will be marked on the drywall prior to hanging. I no longer have to take the time to measure and mark the centers of boxes and light cans beforehand. It's just a matter of putting these in and hanging them There is no more measuring to be done. There are no cons that I can think of. Despite the slight drawbacks I discovered during the installation, I am still very pleased with these center mark You should buy them no matter what the price is.

Addilyn Benson

| Jun 24, 2021

A drywall hanger who uses these may never need to use them. As a result they take too much time to attend to them and they do not need them. These can be a great buy for those who hang drywall and do DIY projects occasionally. If you plan on cutting out the boxes, you will likely use a drywall saw rather than a rotary zip cutter. If you are trying to get a tight fitting cut, it can be a challenge You will have a much easier time out. This is not an easy task, but it is It is more useful to me to have the one with a receptacle rather than the one with a recess can. Nowadays, I install LED wafer lights in my custom built homes. They don't require a recess can in order to work. The problem is how to go about it you cut out a hole, remove the wire, wire up the junction box, feed it through the hole, and install the clip - Light emitted from wafers. Now that I rarely use recess can housing, I don't have to use it at all. I can see how that tool would work if you had to install them to get the perfect alignment, but I doubt you would use it for that purpose. If you prefer, retrofit your existing system The housing must be installed after the drywall has been installed.
and
These devices are labor saving and work by magnetism, and you can pretty much guarantee a good mark and fitting. It is hoped that you will not have to fill in missing drywall around electrical boxes and cans using this kind of tool. With this method, you will achieve a more airtight installation, in addition to enjoying labor savings. The best rating in the world.

Rayna Smith

| May 10, 2021