TEKTON Offset Screwdriver Set (3-Piece) | 2944
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
They have three different size screwdrivers, along with three different screwdriver sizes for each type of screw head length of the vines is about three feet A half inch, a four inch, and a five inch The size of the legs on each of the ends is small to large, and from the driver tip to the upper edge of the bend they measure about 1". A little over an eighth inch and one inch 7/16" in diameter. There is a 3/16", 1/4", and 5/16" shaft thickness, which means that the tip width or size is 3/16", 1/4", and 5/16" respectively.
In a really tight spot between the bathroom sink and the front wood panel, I needed a screwdriver. As the cabinet was being assembled, the sink was being dropped in. A knob was missing from the false front, so it needed replacing. Approximately 1 1/2" of space is needed to remove the screw. It worked perfectly with the small one. Although I likely will not come back to it, I am glad I bought it. I would recommend this.
There is no need to worry, it's not too
Selected User Reviews For TEKTON Offset Screwdriver Set (3-Piece) | 2944
In fact, it did not). Yes, it's a slow partial turn of the screw with the offset tool, but it gets into the gap and gives plenty of leverage to turn it (the largest driver is about 5 1/2" long. Middle size approximately 4"), as long as sufficient pressure is applied at the end of the screwdriver to prevent the tip of the screwdriver from coming up out of the screw head slots when The only thing I find disappointing about them is that their ends aren't even shorter than they are, as that might allow them access to tighter places. A driver of the largest size is roughly an inch and a half long from the rounded tip to the top of the curved end, and the middle size is about an inch and a quarter. Only about an inch separates the tip from the top of the bend of the small size. The set as a whole was good.
The tool served its purpose in fixing the rearview mirror on my car, and it did the job well. A solid foundation.
After reading the negative reviews about this item, I was almost not interested in purchasing it. My sewing machine's needle plate is secured by an incredibly tight screw, and I have attempted to remove it but have had no luck. I tried this out for a few days, but became frustrated and purchased it. My two seconds to remove that same screw took two seconds. With this tool, I was amazed at how easy removing the screw was. I had no problem with it. It is a very useful tool and I am glad I bought it.
Press your foot to the floor. The screws weren't able to be turned with normal screw drivers.
As much as anyone else, I adore a good ratcheting screwdriver, but we all know how dangerous one is, as it makes it so easy to turn the screw that we risk overturning it, and, in the case of me, this often happens. They come in handy when you're tightening a screw that's been fit into a tight spot, when you only have a bit of room to turn the screw. As a result of its handle style, I get enough torque to be able to tighten a screw that is tightly fitted into old wood (my most common application), without having to be so tight that I accidentally break a I find the three different sizes convenient, but the medium is what I need most often (since I typically use a size 10 screw and a size 12 screw). Hopefully you will have a lot of success.
I was not expecting the volume set to arrive in such a large form factor. It is too large to be useful unless you are in a tight space, but I needed it to drive into tight spaces. There will not be much of a difference if your clearance to the screw is less than 2".
A merger. Screwdrivers supplied with the machine will not work in that kind of a space.
It's a great price and it has a great Will not hold up, however! As I used them, the screwsharp heads sheared off somewhat. As a result, I didn't get as much use out of them as I would have liked. Turning the screws by hand would have damaged the tool because they were too weak. It looked like the metal on the heads was brittle and soft.