Collins Tool Miter Spring Clamp Pliers (clamps sold separately)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Without a doubt! This was the most important factor when it came to purchasing the product. When you use this product when you do crown molding, you're doing it right.
I saw a few, yes. Because the spring clamps have pointed ends, they leave a small depression in the ground. Painting covers it with a little of the filler and paint. You can stain them and cover them with a little wood filler, so they aren't noticeable. I am a professional carpenter and woodworker and I don't have a big concern about the holes in these clamps compared to not using any clamps at all.
It appears that using pliers is the easiest way to control these springs, as they are very stiff. When squeezed, the jaws of the pliers open the springs. Once you have the spring in position, you release it. There is a possibility that you could use it without the special pliers if you have the hand strength. It may be easier to use regular pliers, however it may be a little
I actually purchased a 12 pack of nails that fit perfectly in the clear plastic case that comes with the Paslode nails
Selected User Reviews For Collins Tool Miter Spring Clamp Pliers (clamps sold separately)
Miters have been a challenge for me for some time now, and I have tried several clamps, gizmos, and this is something that I discovered on YouTube to consider. I have never used these before, yet they have been As an upholstery artist, I make small boxes from hardwoods and I need control over my miters.
These are a game changer for me immediately. These sandpapers are easy to use, very strong, and don't have any rough edges, so any evidence can be easily sanded off. Despite the tool being nice and working great, it comes with a free carabiner that you can use to store all of the clamps. With this purchase, I am supporting mine and their communities by purchasing a product made by Americans for me. It's a great idea.
If I'd known about it when I was doing crown molding and gluing up mitered corners, it would have saved me a lot of time. There is nothing more brilliant than something so simple. Having to deal with the miter joint and closing up any gaps is one thing, but you also have to contend with the multiple curves in the crown profile cut. Because there are only two very small points of contact, you can clamp it to just about any curved surface on the crown. As you clamp these, it is logical to do so in the troughs of contour changes in the crown, so that no markings pass from the process to the I am speechless. The fact that you can do that makes me absolutely giddy. Furthermore, I am using this product to do flat goods, such as outside corners on baseboards and door jambs, without leaving any impressions or marks on the surface. By using this clamp, I am now able to glue up miters without the need to pin nail the miters together in order to keep them in contact while my wood glue sets. Despite not having tried it yet, I suspect one could also hang picture frames by using band clamps, although I have not tried this. I am currently ordering more springs, so as to speed up the process of holding multiple miters together at the same time.
These mouldings can be used for crown moulding. I really appreciate how useful they are for what they are. A tight outside miter with enough pressure for a good match, but you can still "steer" the profiles for a good fit. The needle end of the springs were more appealing to me than the gouge from the The only improvement that could be made is a spring to retract the jaws of the plier, but I used the rubber band that came with it to do.
It's finally here. It is imperative that you get the pliers, so it is best if you buy them together. The springs are so difficult to press apart (must be this way to work), so you will have to search through your whole garage for something to pry them apart. I used my Knipex pliers but it was a workaround solution that took longer than expected. You will need these clamps along with the pliers. If you are planning on doing one picture frame, it will not hurt to get two sets of four clamps. Glue should be applied evenly and a maximum pressure is achieved if your frame is wide or curves inward by setting four clamps on top, and four at the bottom of each mitered corner. The corners of the picture frame should be glued at the same time with Titebond 3. The glue will not seep through the deck and can be cleaned easily and thoroughly. The corner of the paper should be pinch-joined using pliers. After that, do the corner on the other side Next, we'll move on to To clean the front of the frame, use a damp cloth to wipe the excess glue away. You could also clamp the bottom of the frame if you can. Flip the frame face down, and flip it face up after that. It is necessary to do this for frames that are curved. You will not need to level the frame if it lies flat on the ground. You can clean the other side of the glue, or you can let it dry and then scrape it off with a sharp tool.
When I saw this on YouTube, I thought that it would be an awesome idea to use for crown mounding, bases, Leaving a mark from the point of the clamp yet with a little filler around the base or crown of your paint grade base or crown, you're My method of gluing was going wet one side, gluing the other, clamping while it set, and finishing it with a nail (if) necessary. Here's what I came up with. This would have been helpful if I had known about it sooner.
It was easier to hold the corners in place while I nailed the boards in place when I was working alone. Clamps that work on 90 degrees cannot be used with regular clamps. Orienting the clamp to work around low ceilings and trim close to the wall or floor was also a bonus for me. I can't think of anything better (so I didn't deduct any stars) - the only negative is that there is no better alternative. A sharp point protrudes from the clamps, and they dig into the surface Once the clamp is removed, the wood is left with tiny holes. This book is highly recommended- That's exactly the kind of tool I need.
I've seen others use them and they seemed like they were gimmicks. Having read a trusted online review, I decided to try them. In fact, they work really It's important to let the glue set up on the outside corners. I plan to use cyanoacrylate glue on those. Things can be sped up with glue. It doesn't take much time to learn. Besides the pliers, there are 4 spring clamps included in this set. There is a chance that I/you will need more than 4 springs for a bigger project. Yes, I would buy from you The hint is You can buy a $1 hardware store gift card.
The oak serving trays I made are all from oak. During the day, the hopper is open at the top. Because bars or screw clamps would slip off the joints, it was impossible to clamp them together. I attached two spring clamps to each joint and they worked perfectly. As a method of protecting the side and end wood faces of the joints, I used double faced tape to attach small protective cleats. My pieces were left with no marks since I removed the cleats after the glue dried. I was happy with the results.
Related Products For Collins Tool Miter Spring Clamp Pliers (clamps sold separately)
