CGTime USB 2.0 A Screw Terminal Block Connector USB 2.0 A Female Plug to 5 Pin/Way Female Bolt Screw Shield terminals Pluggable Type Adapter Connector Converter 300V 8A(2Pack) (Female)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Pins labeled "S", "-" and "--" are present on the board In between", "+" and "D-" You will get "D+" and "F". A Shield or the chassis of a USB plug is indicated by an S. In other words, it's negative supply. A positive supply is indicated by a "+" sign and should be 5 The letter "D" A differential data line "" and "D+" is the difference line.
As long as you match the other side, you can use it as you like for DIY prototype projects that involve voltage/amperage only. There are four terminal tabs, divided into 1+ / 3-positions. Two plus two Three plus one It can also be the other way around. You must know the gauge of the wire in order to safely handle the current and voltage that you wish to move, and to feed your device. Find the gauge of AWG and the POWER TRANSMISSION amperage, and then choose the correct wire. *During testing, be on the lookout for heat coming from the adapters, wires, and power supply.
my set. I haven't used it yet, but it is made of black plastic with letters molded into it. Specifically, if you are looking at the green piece, where you will insert your wire, the terminals are labeled as follows, from left to right A backward S, a +, and a - A-, D-, F There should be a + and a Usually I can't use superscripts here, but I can do so on the D's. In the left hand column, the first symbol appears to be an upper-case D This is the backwards S I zoomed in on it with my phone, and it's definitely not a 2 or a 5. It seems incongruous that there are five screw terminals on the male end, when clearly the female end has only one There are only four contacts on the USB end,
It is not a good idea to It looks like you are doing all the wrong things with your question. it makes any difference at all if I use this plug with 5 volts or another one with 115 volts from my wall outlet? It's like 23 times the difference! Make sure you buy a suitable plug for your project from the hardware store.
Selected User Reviews For CGTime USB 2.0 A Screw Terminal Block Connector USB 2.0 A Female Plug to 5 Pin/Way Female Bolt Screw Shield terminals Pluggable Type Adapter Connector Converter 300V 8A(2Pack) (Female)
This is what you need. The wires on USB are finicky and tiny, so if you've had to do a prototype with it, you know how tricky it is. With this technique, there is no soldering or aggravation involved. The wires should be screwed in and you can begin using it right away. It saves a lot of time. Having said that, these are a little bulky, and I'm not sure I would use them in a final design, but I think they are perfect for mock-ups.
The wire was used to hook up a Nest Through the hole we were able to pass the USB cable easily.
There was a problem with the USB plug on my heated jacket. When it flexed too far, it severed a wire and let it lose power. I was scared about my $150 jacket. After a few minutes, I began looking around and sure enough, I found it! Among the following reasons prompted me to prefer this model over the one that was soldered I will. - The many tiny connections I have to solder are beyond my capacity
- Because I did not want to have to unsolder my work if I made a mistake, I found some wiring diagrams online and followed them. It took about five minutes and my jacket was working as well as it had before. Even though the replacement plug is larger than a factory one, it saved me the hassle and saved a bundle of money. And, since it's a 2 pack, now I have a spare.
With this, I was able to make a low-loss USB power cable.
The existing USB plugs became worn out and failed to link to the system, so the devices had become useless. I'm sure you can thank these Screw Terminal Block Connectors for saving the devices from the My fault was that the connectors in the cables were damaged, so I cut off the damaged connectors and removed the very fine wires. To figure out which wire went to which terminal, I had to perform detective work, but I figured out what was going on by looking at Once I got the wires connected, all was good again and I was able to connect the two USB devices. It was a pleasure to order adaptors from you. The adaptors shipped promptly and they There is one caveat, however It got its protection and reinforcement from the rubbery cable jacket when the wires originally had a very small gauge. When you use an adapter, you lose these features. By using electrical tape as a strain relief device I managed to alleviate the strain on the cable It is likely that the wires would break off if you used the devices without the tape.
I noticed that my Nest Camera was acting weird after the big snow storms in the Northeast. I spent a considerable amount of time in the snow bank with the USB power supply. Visual inspection revealed corrosion and missing conductors on the USB connector of the Nest hub. Since the camera was out of warranty, I took a chance on it. I'm so glad it worked! It's only necessary to have the red and black power cables, no shielded data cables are The picture belongs to James from 2018, I have used it since it worked for me and to show the sequence of connections correctly.
The USB port can be used to power an electronics project using the power.
In general, they work as expected, but the screws holding the wires down are not very strong and can easily be.
Related Products For CGTime USB 2.0 A Screw Terminal Block Connector USB 2.0 A Female Plug to 5 Pin/Way Female Bolt Screw Shield terminals Pluggable Type Adapter Connector Converter 300V 8A(2Pack) (Female)
