Dolphin DC-100S Super B Connector w/Sealant 100 Pcs.
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
These connectors are only for wires that are very small gauge, which is the only use I have for them. The gauge could be 16 gauge, but it may be made of
There is probably no problem with 26 ga cat5 cables as I have run up to 3 plenty of times just fine. However, that is for communications cables like POTS/cat3 and It is unlikely you can use one of these connectors with cat5 and maintain 100Mbps or even 10Mbps speeds in an actual network application. Punchdown splices are available and can be made by crimping two RJ45s and connecting them with an F-type connector Connect one end of the rj45 keystone to the female end of the F coupler and the other end to the Rj45 keystone. It is impossible to sew together three cables in a cat5 network for any reason. *br>The point being that if you are using it for POTS wires, it is still
The temperature is not too high
Adapters can be connected to this connector in 16-way mode Wires 24 gauge and above are also available, as well as the 3M UY2, whose two ports accept any solid copper conductor combination between 19-23 gauges. It is supposed to be 26AWG Approximately 9 mm x 98 mm – 4 mm) filled or air core cable with an insulation rating of The term refers to I received a "082" mm inches)
Selected User Reviews For Dolphin DC-100S Super B Connector w/Sealant 100 Pcs.
They are perfect for the work I do (security alarm and CCTV technician). I use them almost every day for low voltage wiring. There is no contest on price and I don't think there is a cheaper alternative. Dolphins (blue or white) are a great product. In my opinion, the blue ones are better as they have a silicone sealant inside the connector (vs the white, which do not), which means that water and other contaminants have a harder time penetrating the splice. A simple process of I love the crimp too, and they usually hold together well if I need to reuse them after a splice. Connectors made by Dolphin are the only ones I will use.
These are older than I am and I have trying to find something similar but I have not found anything similar so I finally had to go online to purchase them. Their coating on the inside makes them seal better than any other wire connector. The coating helps to form a connection and keep moisture out. A twist and a crimp is all that's needed to open the bag. I have only one complaint, and that is that these are so small that certain larger gauge wires don't However, these would be a good fit for small electronics and car audio.
It's amazing how well they work for splicing together RGB LED lights, 18-inch I especially suggest. If you are in a rush and don't have time for soldering or shrink-wrapping. To crimp with, I used this tool and regular pliers (the part with the jagged jaws). When I remove the shielding and twist them together, then clamp one of these, it seems to work better for me. Finally, wrap it in electrical tape or liquid electrical tape to finish it off. My LED(s) were repaired quickly and easily in the field for a Christmas Light display, in this case.
The connectors in question are the best in their class. To reduce the risk of tripping, I still strip and twist the wires before inserting and crimping them. can be easily installed on a ladder while standing on top and do not require any special crimpers to implement It is convenient to use needle nosed or duck bill pliers equipped with a non-knurled side since they are the most functional. Any place that might get damp will benefit from filled ones, as corrosion will be prevented from affecting the connection. The nonfilled ones are good for places that get very wet, but I dip them in liquid tape if they have to get wet. This is the real Dolphin, not the fake imports from China It was at least at the time this review was written.
In contrast to what is shown in the photo, the product received was different. Dolphin is not printed on the connector, but they appear to be the same. There is no way I can give an opinion on how the performance differs from the brand name, and it might also be the same connector just without the branding for a cheaper option.
Making the job fast and easy was made possible by this technique. As of now, there hasn't been an issue.
This is a fantastic product that I cannot comprehend why it was discontinued. THE PRODUCT IS PERFECT AND THE SELLER SHIPPED ASAP, THANK YOU FOR THE QUICK SHIP MEANS THAT THIS TRANSACTION WAS A PASS!.
The maximum gauge should not be higher than 16 gauge. There is no risk of wire stripping with this tool. The wires are stripped then twisted, then a splice cap is put on, and the splice is squashed. The edge can be pressed to cause it to open again. The low voltage version is perfect.