Siemens Q2020 Two 20-Amp Single Pole 120-Volt Circuit Breakers, for use only where Type QT breakers are allowed
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
The FEEQ needs to be replaced" There is a 15 amp circuit. Here's what you should do. My understanding of the question was unclear or my answer did not fully explain how it should be answered. You might replace it with the same type of breaker or 2 20 amp breakers of the same type
This is not a Siemens panel, as I think I put it in another It has been my experience that getting the same brand of breakers as the panel is the best way to be sure.
There are many differences between a Brayant breaker and an attack on the defense. There is a CLASSIFIED breaker available from Siemens that can be used ONLY with certain Square D panels as shown on the BR breakers from Cutler Hammer are suitable for Bryant, Challenger and Westinghouse panel boards, for instance. The Bryant BR Eaton/Cutler hammer is the same as the Eaton/Cutler BR Bryant hammer. Thanks a lot!
A ITE breaker box is connected to my electrical system. This Siemens brokeer fit perfectly! Had a hard time finding a breaker that would work!
Selected User Reviews For Siemens Q2020 Two 20-Amp Single Pole 120-Volt Circuit Breakers, for use only where Type QT breakers are allowed
The lowest four slots of the cabinet are usually occupied by cards. At those lower locations, the buss bars are notched to fit the CT style breakers (as well as the standard breakers). This type of breaker has a locking mechanism The tab on the edges of them prevents them from being installed in other locations, and thus limits the total number of circuits that can be installed into the In fact, adding to the confusion is the fact that there is a "NON-" This breaker is now available in a new "CTL" version (QT2020NC) with no lock-in mechanism These products have the same bar code and stock number as those offered at Lowes, and they are sold with the "Fold out" feature. QT2020NC are available from HODO and are priced higher at $24+ than their actual cost of $9+. Please refer to the pictures below for a clearer idea of the difference between the CTL and non-CTL A CTL version of this breaker is available. There will always be limitations when it comes to fitting QT breakers in your breaker panel, even if the label states that it accepts QT breakers. It is necessary to move the breakers around in those slots if they have standard width breakers already in them in order for the CTL style breakers to fit in those slots. The issue is not whether the panel is of QP or QT style, but whether it is of CTL or not was This panel has the CTL slot located on it.
It's just that I'm in the middle of a heat wave, so I'll give up on this, but Amazon needs to up their game just a little bit. On the other hand, at least in this instance, I am upset with Amazon. It should be possible to get exactly what is advertised in electrical equipment. There is nothing more or less to say. It's fortunate I'm an electronics technician, and I have some idea what electrical stuff means. There is a 5 amp short in this breaker. I should use a 20 amp breaker for what this is replacing, according to electrical codes. In light of the fact that this will not cause a fire, but rather a headache, it serves as an adequate if it is the wrong one, you must be ready to send it back.
The Siemens 125A breakers came with these when I purchased the Siemens My box does not come with lugs that fit these. I don't think the slot is deep enough for the lug. These are only available at our local Big Box stores for 2 pole breakers. The single pole breakers are the best option for me.
Then why not gain full control over your circuitry from the very.
Verify that your panel is capable of supporting tandem breakers. My application hasn't yet been tested with this product, but I'm sure it would be fine. You can see on your panel where the two types of breaker go by looking at the diagram. We're sad, but generally happy with the product. For those who are unsure if it will fit, it is most likely that your panel will not accept tandem breakers. First, the blade MUST have a slot cut out of it by the manufacturer! Installation must be completed before installing in order to stay within the specs and code.
I am having a problem with the circuit breaker on my old ITE panel. No reason was given for it to trip. By moving to a different breaker, I verified that the wiring is OK. Home Depot and most other hardware stores are not equipped with them. Here is my 1- I check it This is said to be Model QP, which is 18 inches C/B. The QT breaker (called QT because it is 1/2 in size and has two Earlier, I read a comment from another reviewer that it would not work. It was refuted by another person and said it was consistent with the In the end, I bought two of these 20A QTs and one of these 15A QTs. As a result of free shipping, I bought an extra one, and now I keep it for spares, since ITE panels have a hard time being found C/B. This outfit fits perfectly and is very move my hips a little in order The purpose of this is to verify it is in fact compatible.
It was a total waste of time and money. They were cross threaded and the wire couldn't be tightened because the screws didn't come close to coming close to it. It is now damaged due to the crack that formed when I tried to replace the screws. It does not make me.