HPDMC 4500psi Yolk Fill Station for HPA Tanks - High Pressure Gauge - Aluminum Alloy Refill Adapter - 36in Teflon Hose - DIN Valve for PCP Paintball Tank Charging System (Black)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Filling air guns with the fitting and hose shown here is done by connecting it to a diving tank, and the fitting controls the amount of air going into the air pressure chamber of the gun. For the guns to be filled, the scuba tank has to already be filled with air.
Yes, there are ones made that do that.
There's no DIN / screw in valve attached to it. Generally, this is what K-series is Valve (yoke is typical of most USA diving tanks). Right out of the box, I was able to use it with my scuba tank and PCP Marauder. The device does not require any adapters.
Thank you. I had a question for you. I'm not sure what kind of air rifle quick connects you use. There are 8mm quick disconnects on this valve.
Selected User Reviews For HPDMC 4500psi Yolk Fill Station for HPA Tanks - High Pressure Gauge - Aluminum Alloy Refill Adapter - 36in Teflon Hose - DIN Valve for PCP Paintball Tank Charging System (Black)
The pump may work for short term filling of small bottles, but when used repeatedly for longer term filling of larger bottles, the pump breaks down. It is for filling an 80 cf bottle I use my own compressor and this yoke. It was a little tricky at first when I used it A pressure of 3000 psi caused the rings to blow. While disassembling it, I discovered that the set screw had slag inside of the cavity and that the offset was out of whack. When the rings were assembled at the factory, they were damaged. In order to get rid of the slag, I installed new oil-impermeable liners After we installed the new o-rings we test-ran the pressure and the new o-rings Three thousand pounds of pressure caused the rings to leak. Replaced them again as soon as I could and got to work. As a result, I have not done a pressure test at the upper limit because I do not want to waste it The rings are. It's possible that the yoke I received is defective, but since I won't be filling more than 3500 PSI, I'll give it some time before purchasing a better one. Update It has been fixed and I was able to get it working correctly. It is a resounding victory for The original rings that were installed in it were of An o-ring of the type 010 is widely used in scuba diving There are rings. In their place, I replaced them with metric 10x6x2 o-rings The diameter of this ring is slightly greater than that of A seal was able to be formed when it reached 100. 0. Lastly, I drilled a 3" 1/4 hole in the yoke tightening screw, and installed a 3" 1/4 bolt to act as leverage so that it will seat even The item is now satisfactory to me after I did this.
My Benjamin Armada 0 needed a refill, so I purchased this. The dive was performed using the HP 100 cu ft Steel scuba dive tank with a YOKE valve--SAP 25 (BTAP25). The pros are You're right. * It's working. This fill adapter assembly has the convenience of quick attaching and detaching. The manometer is built into the device. There is a Bleed Relief Valve on this device. was able to open the valve even at 3500 PSI without any difficulty. It is appropriate that the hose be long enough. A well-built product. However, the following cons take away from the quality The following thoughts are other than the one above There is some room for improvement in terms of the hose. In the first 20 refills, there was quite a bit of trouble using the quick disconnect. It would be nice if it came with some type of protection for the air hole when it is not attached The 1st Stage Dust Cap Rubber is similar to a scuba diving regulator.
I only used it once, the female end came undone and the spring fell out, it is a useless piece of garbage, too tight to remove, I would not recommend it to my fellow airgunners, a one-time Is that true? The only thing wrong with me is that I'm not a racist Taking it to the post office, packing it up, and mailing it back.
It is a great product, but is only intended for YOKE tanks. There's no way someone can make this mistake at the point of selling the product. It's very irresponsible, and now I have to buy an adapter for my tank just to use it. I would be fine with that if I knew beforehand. Just change the title.
I used this to fill a scuba tank into my Benjamin Maurader quickly and easily. If the pressure release valve is not turned with pliers under pressure, it can't be turned at all. We should make it easier to turn it if it were more like a wing nut or something you could pull Despite its small size, the knob has a lot of tension.
My rifle goes perfect with the gauge on this device, and it is less than a third the price of what the online air gun stores are charging. I have three other fill probes I use, but this one is much cheaper. I find it useful since I only have to look at one gauge to be sure I get the right amount.
I have no issues with this first of its kind. It is a great way to take care of your PCP, thank you. The local dive shop has a used tank for 10 bucks that I like, so I got it filled and took it on our adventure.
My experience with it has been positive. It is machined correctly and holds securely, and it has never let me down.