Lifetime 60326 Vertical Storage Shed, Pack of 1, Desert Sand
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
It was easy to lay a floor with cement tile blocks we bought at Lowe's While you can set it on dirt, its nice floor base makes it easier to move
Thanks for pointing out that drawing is incorrect. This will be fixed shortly. I'm so sorry for any inconvenience. This shed has a real size of 27 feet. The diameter of the hole is 5 inches. The dimension is 53 inches wide by 29 inches high. I am 6 inches tall. The size of the poster is 67 inches wide. The diameter of 7 inches. The exterior (exterior) of the house is H. I am 7 inches high. The dimensions of the sheet are 52 cm L x 52 cm W. There is 1 inch in it. The dimensions of the piece are 65W x 28H. It is 1 inch. The interior of H (the interior).
The roof is made of the same hard plastic as the sides, but a darker shade. It is important to know that the inside of the shed is not waterproof, but it is possible to make it waterproof. I watered it down from all angles once it was assembleed, but some water was able to enter. In theory, you could use some 1"x3/8" window insulation on the roof to finish it off with a waterproof finish, but I didn't try that
The one we received arrived in just five
Selected User Reviews For Lifetime 60326 Vertical Storage Shed, Pack of 1, Desert Sand
"Be prepared" is a phrase I know from assembling enough of these. Take the time to read the directions several times and to read the review comments before buying. You should not purchase any of the following items if you lack the following tools A ratcheting screw driver with multiple Philips bits*A cordless torque drill*A straight metal pick*A rubber mallet*As for the directions, below are errors and suggestions for each step 1. Remove the packing tape located at the top of the page. A numbered system for describing the steps. *Brief description here There should be a "L" instead of an "R" in both the last sentence and the diagram. A rubber mallet is used to push the metal bar into the opening by aligning the panel with the wall and aligning the metal bar with the opening. It would be okay to define "a few inches" as 2 inches since the bar will be pushed completely into the panel at a later stage. *Brief description here "L" should be read as "R" instead of "L" in the last sentence and on the diagram. *Brief description here There is no difference between steps 9 and 10. Be sure that all loose plastic parts have been removed from holes before they are fastened. *Brief description here It is not necessary to tighten the fasteners initially. Assembly should be loose, then the fittings should be tightened. *Brief description here It is not recommended that you tighten the fasteners immediately after installation. Assembly should be loose, then the fittings should be tightened. Flexing of the metal bar is evident. *Brief description here Set up a self-checkout system After tapping screws, you need to clean them up. Through the metal they will make a few cuts in a few seconds. *Brief description here 15 Be sure that the holes are aligned before fastening them with a straight metal pick. 1. *br. To align the holes of the metal bars with the dimples for the hinges in step 2, visualize the alignment. 1. *br. As in step 2, align the metal bar holes with the dimples for the hinges using the mirror image. It should be fastened to the metal bar at 16 before the bolt. 1. *br. In order to install the bar into the opening the panel needs to be placed against a wall and aligned with the opening. Push in the metal bar 1. *br. Parts 13 and 14 do not match the holes as shown. A straight metal pick will allow you to better align the holes and help you hammer the bolts through. You must align the square sides of the bolts with the square openings in the 1. *br. There was a problem with the drill bit. In the end, however, I am able to use the remainder of the funds to pre-finance Sure, I'm a pre-electronic According to the instructions, drill these holes. Three eighths of an inch is all that is required to expose the bit. The numbers 20 and 2 are the same. This process should have occurred prior to the installation of the door, in my opinion.
Once we received the shed, we had a great deal of anxiety about assembling it. Putting together a simple box took hours, parts did not line up, and there were gaps in the holes. It is the mallet that is most important. It's a bummer being Hindges.
I was concerned about reviews stating that the product was damaged when it arrived. I was unsatisfied with the condition of the package as soon as it was off the It is possible that the product could/should be packaged more effectively. In any case, all pieces arrived in perfect condition, with all hardware and instructions. There are no missing parts. In fact, if you are not a regular do-it-yourselfer, you will get frustrated during certain parts of the assembly process. It took me about four hours to complete and I followed directions using the right tools. I found the hinges to be challenging, but I completed it without incident. Additionally, if you are assembling in a small area, you will need to be able to lie down or lie forward in order to access the underside once your panels and walls have been attached to the floor. There are a lot of things I like about it, especially how it looks. I did not give 5 stars on weatherproof since the seams were sealed with two inches of vinyl tape on both sides, and with the anchors securing the roof to prevent it from moving in windy weather, I will run a cable over the top to prevent it from moving. It'll be interesting to see how it holds up when it's battered by a Tropical Storm.
I found it difficult to put together the curved sides at the back of the unit since the "tabs" at the bottom did not fit well, so doors did not go on easily. There was a lot of hardware missing from the box, so it had to be purchased,.
The decision about which shed would be the "right" one was not an easy one for me. I did a lot of research and then more. Lifetime is a company I am familiar with we have a picnic table and a basketball hoop that is the same brand. Winters in the Midwest are tough and these hold up well. There was a mistake with the vertical bars on the shelves, directions are reversed. Someone mentioned this in a previous review, but I forgot to fix it until I nearly drove myself insane trying to attach the When you realize that the directions are incorrect, there is only one way to attach the shelves, and it is quite simple. My assembly took about two hours without any help and I assembled it all by myself. I found the rest of the directions very straightforward and easy to understand. There are holes near the bottom door where water can get in, but this shed can be used to store garden equipment or kids toys very well. It would be nice if there were more shelves or hooks in the interior.
There is no hardware in the It is true that these are challenging times, but the customer service number is unavailable. The date of the inauguration is April 20, 2021 My hardware packages have finally arrived and I have been able to speak to Customer Service. I got it assembled and I love it! It was a challenge, but not impossible.
Assembling it was difficult due to the lack of instructions that came with it. To download digital copies, I had to go to their website. I can only give 4 stars due to this.
There are no brackets for the shelves, and it's not so easy to put together. It's difficult to close the doors. You have to force them shut. The doors have a gap on the top corner of the frame, so regardless of what you do, water can come in.
Related Products For Lifetime 60326 Vertical Storage Shed, Pack of 1, Desert Sand
